View GMS87C1202_1245392.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
GMS87C1102 / GMS87C1202
CMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
1. OVERVIEW
1.1 Description
The GMS87C1102 and GMS87C1202 are an advanced CMOS 8-bit microcontroller with 2K bytes of ROM. The HYUNDAI MicroElectronics GMS87C1102 and GMS87C1202 are a powerful microcontroller which provides a highly flexible and cost effective solution to many small applications. The GMS87C1102 and GMS87C1202 provide the following standard features: 2K bytes of ROM(OTP), 128 bytes of RAM, 8-bit timer/counter, 8-bit A/D converter, 10-bit High Speed PWM Output, Programmable Buzzer Driving Port (GMS87C1202 only), on-chip oscillator and clock circuitry. In addition, the GMS87C1102 and GMS87C1202 support power saving modes to reduce power consumption. This document is only explained for the base of GMS87C1202, the eliminated functions are same as below.
Operating Temperature -20C~+85C -20C~+85C -40C~+125C -40C~+125C
Device name GMS87C1102 GMS87C1202 GMS87C1102E GMS87C1202E
OTP Size 2K bytes 2K bytes 2K bytes 2K bytes
RAM Size 128 bytes 128 bytes 128 bytes 128 bytes
I/O 11 15 11 15
BUZ NO YES NO YES
INT1 NO YES NO YES
Package 16DIP/SOP 20DIP/SOP 16DIP/SOP 20DIP/SOP
1.2 Features
* 2K bytes On-chip Program Memory * 128 Bytes of On-Chip Data RAM * Minimum Instruction execution time: - 500ns at 8MHz (2cycle NOP Instruction) * 2.7V to 6.0V Wide Operating Range * Basic Interval Timer * Two 8-Bit Timer/ Counters * 10-Bit High Speed PWM Output * Two external interrupt ports (GMS87C1102 has one external interrupt port) * One Programmable Buzzer Driving port (GMS87C1202 only) * 15 Programmable I/O Lines (GMS87C1102 has 11 programmable I/O lines) * Seven Interrupt Sources (GMS87C1102 has Six interrupt sources) * 8-Channel 8-Bit On-Chip Analog to Digital Converter * Watch dog timer * Oscillation : - Crystal - Ceramic Resonator - External Oscillator - RC Oscillation * Power Down Mode - STOP mode - Wake-up Timer mode - RC-WDT mode * Power Fail Processor ( Noise Immunity Circuit )
1.3 Development Tools
The GMS800 family is supported by a full-featured macro assembler, an in-circuit emulators CHOICE-Dr.TM, and add-on board type OTP writer Dr.WriterTM . The availability of OTP devices is especially useful for customers expecting frequent code changes and updates. The OTP devices, packaged in plastic packages, permit the user to program them once.
In Circuit Emulator Assembler OTP Writer CHOICE-Dr. HYUNDAI MicroElectronics Macro Assembler Dr.Writer
Oct. 1999 ver 1.0
1
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
2. BLOCK DIAGRAM(GMS87C1202)
PSW
ALU
Accumulator
Stack Pointer Data Memory
PC
Program Memory Interrupt Controller RESET System controller System Clock Controller Timing generator Xin Xout Clock Generator 8-bit Basic Interval Timer Watch-dog Timer 8-bit A/D Converter 8-bit Timer/ Counter High Speed PWM Buzzer Driver Instruction Decoder Data Table
VDD VSS Power Supply RA0 / EC0 RA1 / AN1 RA2 / AN2 RA3 / AN3 RA4 / AN4 RA5 / AN5 RA6 / AN6 RA7 / AN7 RB0 / AN0 / Avref RB1 / BUZ RB2 / INT0 RB3 / INT1 RB4 / CMP0 / PWM RC0 RC1 RA RB RC
3. PIN ASSIGNMENT(GMS87C1202)
20 DIP
AN4 / RA4 AN5 / RA5 AN6 / RA6 AN7 / RA7 VDD AN0 / AVref / RB0 BUZ / RB1 INT0 / RB2 INT1 / RB3 PWM / COMP0 / RB4 AN4 / RA4 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 RA3 / AN3 AN5 / RA5 RA2 / AN2 RA1 / AN1 RA0 / EC0 RC1 RC0 VSS RESET Xout Xin AN6 / RA6 AN7 / RA7 VDD AN0 / AVref / RB0 BUZ / RB1 INT0 / RB2 INT1 / RB3 PWM / COMP0 / RB4 1 2 3 4 5 6 7 8 9 10
20 SOP
20 19 18 17 16 15 14 13 12 11 RA3 / AN3 RA2 / AN2 RA1 / AN1 RA0 / EC0 RC1 RC0 VSS RESET Xout Xin
2
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
4. BLOCK DIAGRAM(GMS87C1102)
PSW
ALU
Accumulator
Stack Pointer Data Memory
PC
Program Memory Interrupt Controller RESET System controller System Clock Controller Timing generator Xin Xout Clock Generator 8-bit Basic Interval Timer Watch-dog Timer 8-bit A/D Converter 8-bit Timer/ Counter High Speed PWM Instruction Decoder Data Table
VDD VSS Power Supply RA0 / EC0 RA1 / AN1 RA2 / AN2 RA3 / AN3 RA4 / AN4 RA5 / AN5 RA6 / AN6 RA7 / AN7 RB0 / AN0 / Avref RB2 / INT0 RB4 / CMP0 / PWM RA RB
5. PIN ASSIGNMENT(GMS87C1102)
16 DIP
AN4 / RA4 AN5 / RA5 AN6 / RA6 AN7 / RA7 VDD AN0 / AVref / RB0 INT0 / RB2 PWM / COMP0 / RB4 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 RA3 / AN3 RA2 / AN2 RA1 / AN1 RA0 / EC0 VSS RESET Xout Xin AN4 / RA4 AN5 / RA5 AN6 / RA6 AN7 / RA7 VDD AN0 / AVref / RB0 INT0 / RB2 PWM / COMP0 / RB4
16 SOP
1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 RA3 / AN3 RA2 / AN2 RA1 / AN1 RA0 / EC0 VSS RESET Xout Xin
Oct. 1999 ver 1.0
3
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
6. PACKAGE DIMENSION(GMS87C1202)
20 DIP
unit : mm
TYP 7.62 26.20.3 6.540.3
MAX 4.57
MIN 0.38 3.30.25
0.460.07 1.450.2
TYP 2.54
0 ~ 15
0.250.05
20 SOP
7.50.1
10.350.2
12.80.2 0.20.1 0 ~ 8 0.420.08 TYP 1.27 0.260.05 0.70.3
2.50.15
4
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
7. PACKAGE DIMENSION(GMS87C1102)
16 DIP
unit : mm
TYP 7.62 19.20.2 6.30.3
MAX 4.32
MIN 0.38 3.30.25
0.750.3 0.460.07 1.450.2 TYP 2.54
0 ~ 15
0.250.05
16 SOP
7.50.1
10.350.2
10.250.05 0.180.05 0 ~ 8 0.420.08 TYP 1.27 0.270.04 0.70.3
2.50.15
Oct. 1999 ver 1.0
5
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
8. PIN FUNCTION
VDD: Supply voltage. VSS: Circuit ground. RESET: Reset the MCU. XIN: Input to the inverting oscillator amplifier and input to the internal clock operating circuit. XOUT: Output from the inverting oscillator amplifier. If RC Option is used, the oscillator frequency divided by 4 (Xin/4) comes out from Xout pin. RA0~RA7: RA is an 8-bit, CMOS, bidirectional I/O port. RA pins can be used as outputs or inputs according to "1" or "0" written in the Port Direction Register(RAIO).
Port pin RA0 RA1 RA2 RA3 RA4 RA5 RA6 RA7 Alternate function EC0 ( Event Counter Input Source ) AN1 ( Analog Input Port 1 ) AN2 ( Analog Input Port 2 ) AN3 ( Analog Input Port 3 ) AN4 ( Analog Input Port 4 ) AN5 ( Analog Input Port 5 ) AN6 ( Analog Input Port 6 ) AN7 ( Analog Input Port 7 ) Table 8-1 RA Port PIN NAME
VDD VSS RESET XIN XOUT RA0 (EC0) RA1 (AN1) RA2 (AN2) RA3 (AN3) RA4 (AN4) RA5 (AN1) RA6 (AN1) RA7 (AN7) RB0 (AVref/AN0) RB1 (INT0) RB2 (INT1) RB3 (BUZ) RB4 (PWM/COMP0) RC0 RC1
In addition, RA serves the functions of the various special features in Table 8-1. RB0~RB4: RB is a 5-bit, CMOS, bidirectional I/O port. RB pins can be used as outputs or inputs according to "1" or "0" written in the Port Direction Register(RBIO). RB serves the functions of the various following special features.
Port pin RB0 RB1 RB2 RB3 RB4 Alternate function AN0 ( Analog Input Port 0 ) AVref ( External Analog Reference Pin ) BUZ ( Buzzer Driving Output Port ) INT0 ( External Interrupt Input Port 0 ) INT1 ( External Interrupt Input Port 1 ) PWM ( PWM Output ) COMP0 ( Timer0 Compare Output ) Table 8-2 RB Port
RC0~RC1: RC is a 2-bit, CMOS, bidirectional I/O port. RC pins can be used as outputs or inputs according to "1" or "0" written in the Port Direction Register(RCIO) .
Pin No.
5 14 13 11 12 17 18 19 20 1 2 3 4 6 7 8 9 10 15 16
In/Out
I I O I/O (Input) I/O (Input) I/O (Input) I/O (Input)
Function
Supply voltage Circuit ground Reset signal input
External Event Counter input Analog Input Port 1 Analog Input Port 2 8-bit general I/O ports Analog Input Port 3 Analog Input Port 4 Analog Input Port 5 Analog Input Port 6 Analog Input Port 7 Analog Input Port 0 / Analog Reference External Interrupt Input 0 5-bit general I/O ports External Interrupt Input 1 Buzzer Driving Output PWM Output or Timer Compare Output 2-bit general I/O ports
I/O (Input) I/O (Input) I/O (Input) I/O (Input) I/O (Input) I/O (Input) I/O (Input) I/O (Output) I/O (Output/Output) I/O I/O
Table 8-3 Pin Description
6
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
9. PORT STRUCTURES
* RESET
VDD
Internal RESET
VSS
* Xin, Xout
VDD RC option fxin / 4
1
Xout
0
VSS STOP
To System CLK
Xin
* RA0/EC0
Data Reg. Data Bus
Direction Reg. Data Bus
Data Bus Read EC0
Oct. 1999 ver 1.0
7
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
* RA1/AN1 ~ RA7/AN7
VDD Data Reg. Data Bus
Direction Reg. Data Bus VSS Data Bus Read To A/D Converter
Analog Input Mode (ANSEL7 ~ 1) Analog CH. Selection (ADCM.4 ~ 2)
* RB0 / AN0 / AVref
VDD Data Reg. Data Bus
AVREFS Data Bus
Direction Reg.
VSS Data Bus Read To A/D Converter
Analog Input Mode (ANSEL0) Analog CH0 Selection (ADCM.4 ~ 2)
1
Internal VDD To Vref of A/D
0
AVREFS
8
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
* RB1/BUZ, RB4/PWM0/COMP
PWM/COMP BUZ Data Reg. Data Bus Function Select Data Bus VSS Data Bus
1
VDD
0
Direction Reg.
Read
* RB2/INT0, RB3/INT1
Pull-up Select Data Reg. Data Bus VDD
Weak Pull-up
Function Select Data Bus INT0 INT1 Data Bus
Direction Reg.
VSS
Read
Schmitt Trigger
* RC0, RC1
VDD
Data Reg. Data Bus
Direction Reg. Data Bus VSS Data Bus Read
Oct. 1999 ver 1.0
9
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
10. ELECTRICAL CHARACTERISTICS
10.1 Absolute Maximum Ratings
Supply voltage ........................................... -0.3 to +6.5 V Storage Temperature ................................-40 to +125 C Voltage on any pin with respect to Ground (VSS) ............................................................... -0.3 to VDD+0.3 Maximum current out of VSS pin ........................200 mA Maximum current into VDD pin ..........................150 mA Maximum current sunk by (IOL per I/O Pin) ........25 mA Maximum output current sourced by (IOH per I/O Pin) ...............................................................................15 mA Maximum current (IOL) .................................... 150 mA Maximum current (IOH).................................... 100 mA
Note: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
10.2 Recommended Operating Conditions
Specifications Parameter Symbol Condition Min. Supply Voltage VDD fXIN=12MHz fXIN=4.2MHz VDD=4.5~6.0V VDD=2.7~6.0V GMS87C1102/GMS87C1202 GMS87C1102E/GMS87C1202E 4.5 2.7 1 1 -20 -40 Max. 6.0 V 6.0 12 MHz 4.2 85 125 C Unit
Operating Frequency
fXIN
Operating Temperature
TOPR
10
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
10.3 DC Electrical Characteristics - GMS87C1102, GMS87C1202
* (VDD=4.5~6.0V, VSS=0V, fXIN =1MHz~12MHz, TA=-20C~+85C)
Specification Test Condition Min 0.8VDD VDD=4.5~6.0V 0.8VDD 0.7VDD 0 VDD=4.5~6.0V 0 0 VDD = 5V, IOH = -2mA VDD = 5V, IOL= 10mA VIN = VSS~VDD VDD = 5V, VIN = VSS -350 2 VDD=5.5V, fXIN=8MHz VDD=5.5V, fXIN=12MHz VDD=5.5V, fXIN=8MHz VDD=5.5V, fXIN=12MHz VDD = 5.5V, fXIN = 8MHz/12MHz VDD = 5.5V 0.5 VDD = 5V, fXIN = 8MHz/12MHz R = 20K, C=24pF 100 300 200 550 -280 3.5 4 6 1 2 0.3 0.2 VDD-1 1 5 15 -200 4 6 10 1.8 3 0.8 2 mA mA uA V uS kHz Typ2 Max VDD VDD VDD 0.2VDD 0.2VDD 0.3VDD V V uA uA V mA V V Unit
Parameter
Symbol VIH1
Pin1 XIN, RESET RB2, RB3 RA,RB0,RB1,RB4,RC XIN, RESET RB2, RB3 RA,RB0,RB1,RB4,RC RA, RB, RC RA, RB, RC RESET,RA,RB,RC XIN RB2, RB33 VDD VDD
Input High Voltage
VIH2 VIH3 VIL1
Input Low Voltage
VIL2 VIL3
Output High Voltage Output Low Voltage Input Leakage Current Input Pull-up Current Power Fail Detect Voltage Normal Operating Current Wake-up Timer Mode Current RC-oscillated Watchdog Timer Mode Current STOP Mode Current Hysteresis Internal RC Oscillation Period ( RC-WDT CLK ) RC Oscillation Frequency ( System CLK )
1. 2. 3.
VOH VOL IIL IIL IPU VPFD IDD
IWKUP IRCWDT ISTOP VT+ ~ VT-
VDD VDD VDD RESET, RB2, RB3
TRCWDT XOUT fRCOSC XOUT
RC0, RC1, RB1 and RB3 pins are applied for GMS87C1202 only. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. This parameter is valid when the bit PUPSELx is selected and set the Input mode or Interrupt Input Function.
Oct. 1999 ver 1.0
11
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
* (VDD=2.7~6.0V, VSS=0V, fXIN =1MHz~4.2MHz, TA=-20C~+85C)
Specification Test Condition Min 0.8VDD VDD=2.7~6.0V 0.9VDD 0.8VDD 0.7VDD 0 VDD=2.7~6.0V 0 0 0 VDD = 3V, IOH = -2mA VDD = 3V, IOL= 7mA VIN = VSS~VDD VDD = 3V, VIN = VSS -100 2 VDD = 3V, fXIN = 4MHz VDD = 3V, fXIN = 4MHz VDD = 3V, fXIN = 4MHz VDD = 3V 0.5 VDD = 3V, fXIN = 4MHz R = 20K, C=39pF 200 200 400 400 -80 3.5 1 0.3 0.1 0.01 VDD-0.7 0.8 5 15 -50 4 3 1 0.6 1 Typ2 Max VDD VDD VDD VDD 0.2VDD 0.1VDD 0.2VDD 0.3VDD V V uA uA V mA mA mA uA V uS kHz V V Unit
Parameter
Symbol VIH1 XIN RESET
Pin1
Input High Voltage
VIH2 VIH3 VIH4 VIL1
RB2, RB3 RA,RB0,RB1,RB4,RC XIN RESET RB2, RB3 RA,RB0,RB1,RB4,RC RA, RB, RC RA, RB, RC RESET,RA,RB,RC XIN RB2, RB33 VDD VDD VDD VDD VDD RESET, RB2, RB3
Input Low Voltage
VIL2 VIL3 VIL4
Output High Voltage Output Low Voltage Input Leakage Current Input Pull-up Current Power Fail Detect Voltage Normal Operating Current Wake-up Timer Mode Current RC-oscillated Watchdog Timer Mode Current STOP Mode Current Hysteresis Internal RC Oscillation Period ( RC-WDT CLK ) RC Oscillation Frequency ( System CLK )
1. 2. 3.
VOH VOL IIL IIL IPU VPFD IDD IWKUP IRCWDT ISTOP VT+ ~ VT-
TRCWDT XOUT fRCOSC XOUT
RC0, RC1, RB1 and RB3 pins are applied for GMS87C1202 only. Data in "Typ" column is at 3V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. This parameter is valid when the bit PUPSELx is selected and set the Input mode or Interrupt Input Function.
12
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
10.4 DC Electrical Characteristics - GMS87C1102E, GMS87C1202E(Extended version)
* (VDD=4.5~6.0V, VSS=0V, fXIN =1MHz~12MHz, TA=-40C~+125C)
Specification Test Condition Min 0.8VDD VDD=4.5~6.0V 0.8VDD 0.7VDD 0 VDD=4.5~6.0V 0 0 VDD = 5V, IOH = -2mA VDD = 5V, IOL= 10mA VIN = VSS~VDD VDD = 5V, VIN = VSS -350 2 VDD=5.5V, fXIN=8MHz VDD=5.5V, fXIN=12MHz VDD=5.5V, fXIN=8MHz VDD=5.5V, fXIN=12MHz VDD = 5.5V, fXIN = 8Mhz/12MHz VDD = 5.5V 0.5 VDD = 5V, fXIN = 8MHz/12MHz R = 20K, C=24pF 80 300 250 550 -250 3.5 4 6 1 2 0.3 0.2 VDD-1 1 5 15 -100 4.2 6 10 1.8 3 0.8 2 mA mA uA V uS kHz Typ2 Max VDD VDD VDD 0.2VDD 0.2VDD 0.3VDD V V uA uA V mA V V Unit
Parameter
Symbol VIH1
Pin1 XIN, RESET RB2, RB3 RA,RB0,RB1,RB4,RC XIN, RESET RB2, RB3 RA,RB0,RB1,RB4,RC RA, RB, RC RA, RB, RC RESET,RA,RB,RC XIN RB2, RB33 VDD VDD
Input High Voltage
VIH2 VIH3 VIL1
Input Low Voltage
VIL2 VIL3
Output High Voltage Output Low Voltage Input Leakage Current Input Pull-up Current Power Fail Detect Voltage Normal Operating Current Wake-up Timer Mode Current RC-oscillated Watchdog Timer Mode Current STOP Mode Current Hysteresis Internal RC Oscillation Period ( RC-WDT CLK ) RC Oscillation Frequency ( System CLK )
1. 2. 3.
VOH VOL IIL IIL IPU VPFD IDD
IWKUP IRCWDT ISTOP VT+ ~ VT-
VDD VDD VDD RESET, RB2, RB3
TRCWDT XOUT fRCOSC XOUT
RC0, RC1, RB1 and RB3 pins are applied for GMS87C1202 only. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. This parameter is valid when the bit PUPSELx is selected and set the Input mode or Interrupt Input Function.
Oct. 1999 ver 1.0
13
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
* (VDD=2.7~6.0V, VSS=0V, fXIN =1MHz~4.2MHz, TA=-40C~+125C)
Specification Test Condition Min 0.8VDD VDD=2.7~6.0V 0.9VDD 0.8VDD 0.7VDD 0 VDD=2.7~6.0V 0 0 0 VDD = 3V, IOH = -2mA VDD = 3V, IOL= 7mA VIN = VSS~VDD VDD = 3V, VIN = VSS -120 2 VDD = 3V, fXIN = 4MHz VDD = 3V, fXIN = 4MHz VDD = 3V, fXIN = 4MHz VDD = 3V 0.5 VDD = 3V, fXIN = 4MHz R = 20K, C=39pF 200 200 450 400 -80 3.5 1 0.3 0.1 0.01 VDD-0.7 0.8 5 15 -50 4 3 1 0.6 1 Typ2 Max VDD VDD VDD VDD 0.2VDD 0.1VDD 0.2VDD 0.3VDD V V uA uA V mA mA mA uA V uS kHz V V Unit
Parameter
Symbol VIH1 XIN RESET
Pin1
Input High Voltage
VIH2 VIH3 VIH4 VIL1
RB2, RB3 RA,RB0,RB1,RB4,RC XIN RESET RB2, RB3 RA,RB0,RB1,RB4,RC RA, RB, RC RA, RB, RC RESET,RA,RB,RC XIN RB2, RB33 VDD VDD VDD VDD VDD RESET, RB2, RB3
Input Low Voltage
VIL2 VIL3 VIL4
Output High Voltage Output Low Voltage Input Leakage Current Input Pull-up Current Power Fail Detect Voltage Normal Operating Current Wake-up Timer Mode Current RC-oscillated Watchdog Timer Mode Current STOP Mode Current Hysteresis Internal RC Oscillation Period ( RC-WDT CLK ) RC Oscillation Frequency ( System CLK )
1. 2. 3.
VOH VOL IIL IIL IPU VPFD IDD IWKUP IRCWDT ISTOP VT+ ~ VT-
TRCWDT XOUT fRCOSC XOUT
RC0, RC1, RB1 and RB3 pins are applied for GMS87C1202 only. Data in "Typ" column is at 3V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. This parameter is valid when the bit PUPSELx is selected and set the Input mode or Interrupt Input Function.
14
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
10.5 A/D Converter Characteristics - GMS87C1102, GMS87C1202
* (VSS=0V, VDD=3.072V/@fXIN =4MHz, VDD=5.12V/@fXIN =8/12MHz, TA=-20C~+85C )
Specifications Min. VSS VSS 3 fXIN=4MHz Conversion Time TCONV fXIN=8MHz fXIN=12MHz fXIN=4MHz AVREF Input Current IREF fXIN=8MHz fXIN=12MHz Typ. 1.3 - 1.0 1.0 0.25 1.0 0.4 0.5 0.6 Max. VDD VREF VDD 1.5 1.2 1.5 1.5 0.5 1.5 20 10 7 0.6 0.8 1 mA S
Parameter
Symbol
Condition AVREFS=0 AVREFS=1 AVREFS=1
Unit
Analog Input Voltage Range Analog Power Supply Input Voltage Range Overall Accuracy Non-Linearity Error Differential Non-Linearity Error Zero Offset Error Full Scale Error Gain Error
VAIN VREF NACC NNLE NDNLE NZOE NFSE NNLE
V V LSB LSB LSB LSB LSB LSB
Oct. 1999 ver 1.0
15
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
10.6 A/D Converter Characteristics - GMS87C1102E, GMS87C1202E(Extended version)
* (VSS=0V, VDD=5.12V, @fXIN =8MHz/12MHz, TA=-40C~+125C)
Specifications Min. VSS VSS 3 fXIN=8MHz fXIN=12MHz fXIN=8MHz fXIN=12MHz Typ. 1.3 - 1.0 1.0 0.25 1.0 0.5 0.6 Max. VDD VREF VDD 2.0 2.0 2.0 2.5 1.0 2.0 10 7 0.8 1
Parameter
Symbol
Condition AVREFS=0 AVREFS=1 AVREFS=1
Unit
Analog Input Voltage Range Analog Power Supply Input Voltage Range Overall Accuracy Non-Linearity Error Differential Non-Linearity Error Zero Offset Error Full Scale Error Gain Error Conversion Time
VAIN VREF NACC NNLE NDNLE NZOE NFSE NNLE TCONV
V V LSB LSB LSB LSB LSB LSB S
AVREF Input Current
IREF
mA
* (VSS=0V, VDD=3.072V, @fXIN =4MHz, TA=-40C~+125C )
Specifications Min. VSS VSS 3 fXIN=4MHz fXIN=4MHz Typ. 1.3 - 1.0 1.0 0.25 1.0 0.4 Max. VDD VREF VDD 1.5 1.2 1.5 1.5 0.5 1.5 20 0.6
Parameter
Symbol
Condition AVREFS=0 AVREFS=1 AVREFS=1
Unit
Analog Input Voltage Range Analog Power Supply Input Voltage Range Overall Accuracy Non-Linearity Error Differential Non-Linearity Error Zero Offset Error Full Scale Error Gain Error Conversion Time AVREF Input Current
VAIN VREF NACC NNLE NDNLE NZOE NFSE NNLE TCONV IREF
V V LSB LSB LSB LSB LSB LSB S mA
16
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
10.7 AC Characteristics
(TA=-20~+85C, VDD=5V10%, VSS=0V)
Specifications Parameter Operating Frequency External Clock Pulse Width External Clock Transition Time External Input Pulse Width External Input Pulse Transiton Time RESET Input Width Symbol fCP tCPW tRCP,tFCP tEPW tREP,tFEP tRST Pins Min. XIN XIN XIN INT0, INT1, EC0 INT0, INT1, EC0 RESET 1 80 2 8 Typ. Max. 12 20 20 MHz nS nS tSYS nS tSYS Unit
1/fCP
tCPW
tCPW VDD-0.5V
XIN
tSYS tRCP tFCP
0.5V
tRST
RESET
0.2VDD
tEPW
tEPW 0.8VDD
INT0, INT1 EC0
tREP tFEP
0.2VDD
Figure 10-1 Timing Chart
Oct. 1999 ver 1.0
17
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
10.8 Typical Characteristics
This graphs and tables provided in this section are for design guidance only and are not tested or guranteed.
In some graphs or tables the data presented are outside specified operating range (e.g. outside specified VDD range). This is for imformation only and divices are guranteed to operate properly only within the specified range.
The data presented in this section is a statistical summary of data collected on units from different lots over a period of time. "Typical" represents the mean of the distribution while "max" or "min" represents (mean + 3) and (mean - 3) respectively where is standard deviation
Operating Area
fXIN (MHz) 12 10 8 6 4 2 0 2 3 4 5 6 VDD (V) 6 4 2 0 2 3 4 5 VDD 6 (V) 8MHz 4MHz Ta= 25C IDD (mA) 8 fXIN = 12MHz
Normal Operation IDD-VDD
Ta=25C
Stop Mode ISTOP-VDD
IDD (A) 0.8 0.6 0.4 0.2 25C , 125C 0 2 3 4 5 VDD 6 (V) 0 Ta = - 40C fXIN=8MHz IDD (mA) 2.0 1.5 1.0 0.5
Wake-up Timer Mode IWKUP-VDD
Ta=25C
fXIN = 12MHz 8MHz 4MHz
2
3
4
5
VDD 6 (V)
RC-WDT in Stop Mode IRCWDT-VDD
IDD (A) 400 300 200 100 4MHz 0 2 3 4 5 VDD 6 (V) fXIN = 4/8/12MHz Frequency affects the current so little. Ta=25C
18
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
IOL-VOL, VDD=5V
IOL (mA) -40C 20 16 12 8 4 4 0 0.2 0.4 0.6 0.8 VOL 1.0 (V) 0 8 25C 125C 12 IOL (mA)
IOL-VOL, VDD=3V
-40C 25C 125C
0.2
0.4
0.6
0.8
VOL 1.0 (V)
IOH-VOH, VDD=5V
IOH (mA) -10 -8 -6 -6 -4 -4 -2 0 4 4.5 5 VOH (V) -2 -40C 25C 125C IOH (mA) -8
IOH-VOH, VDD=5V
-40C 25C 125C
0 2 2.5 3
VOH (V)
Oct. 1999 ver 1.0
19
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
VDD-VIH1
VIH1 (V) 4 3 2 1 0 1 2 3 4 f X IN =4M Hz Ta=25C
XIN
VIH2 (V) 4 3 2 1 VDD 6 (V) 0
VDD-VIH2
f XIN =4M Hz Ta=25C
Hysteresis input
5
2
3
4
5
VDD 6 (V)
VDD-VIH3
VIH3 (V) 4 3 2 1 0 2 3 f X IN =4M Hz Ta=25C
Normal input
VIH4 (V) 4 3 2 1 VDD 6 (V) 0
VDD-VIH4
f XIN =4M Hz Ta=25C
RESET
4
5
2
3
4
5
VDD 6 (V)
VDD-VIL1
VIL1 (V) 4 3 2 1 0 1 2 3 4 5 fXIN=4MHz Ta=25C
XIN
VDD-VIL2
VIL2 (V) 4 3 2 1 f X IN =4M H z Ta=25C
Hysteresis input
VDD 6 (V)
0 2 3 4 5
VDD 6 (V)
VDD-VIL3
VIL3 (V) 4 3 2 1 0 1 2 3 f X IN =4M Hz Ta=25C
Normal input
V IL4 (V ) 4 3 2 1 VDD 6 (V) 0
V D D -V IL4
f XIN =4M Hz Ta=25C
RESET
4
5
1
2
3
4
5
VDD 6 (V )
20
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
FOSC (M H z) 2 .5 2 .0 1 .5 1.0 0 .5 0
T ypical R C O scillator Frequency V S . V D D
C ext= 24 p F Ta=25C
FOSC F requ ency V S . (M H z) C ext= 39p F 1.6 Ta=25C 1.4 1.2 R=20K R=33K
T ypical R C O scilla tor VDD
R=20k 1.0 R =3 3K R = 47 K R = 100 K 0.2 V DD 6 (V ) 0 2.5 3 3.5 4 4.5 5 5.5 VDD 6 (V ) 0.8 0.6 0.4 R=100K
R=47K
2.5
3
3 .5
4
4 .5
5
5.5
FOSC (M H z) 0 .8 C e xt= 1 0 0 p F T a= 25C 0 .7 R =20K 0 .6 0 .5 0 .4 0 .3 0 .2 0 .1 0 2 .5 3 3.5
T ypical R C O scillator F reque ncy V S . V D D
FOSC F O S C (25 C ) 1 .01 0 1 .00 5 1.000
T ypical R C O scillato r F re que ncy V S . T e m p eratu re
C ext= 24 pF R =25K
R=33K 0.9 95 R = 47 K 0 .99 0 R = 1 0 0K 0 .98 5
VDD=5V
VDD=3V
0 .98 0 VDD 6 (V ) 0 .97 5 0 10 20 30 40 50 60 VDD 7 0 (V )
4
4 .5
5
5 .5
Cext
Rext 20K
Average Fosc @ 5V,25C 2.02MHz 1.34MHz 0.952MHz 0.48MHz 1.536MHz 1.012MHz 0.72MHz 0.364MHz 0.78MHz 0.512MHz 0.364MHz 14.11% 11.50% 10.30% 9.07% 14.79% 11.67% 10.42% 9.75% 13.53% 10.35% 9.48%
24pF
33K 47K 100K 20K
39pF
33K 47K 100K 20K
100pF
33K 47K
100K 0.18MHz 7.34% Table 10-1 RC Oscillator Frequencies
Oct. 1999 ver 1.0
21
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
11. MEMORY ORGANIZATION
The GMS87C1202 has separated address spaces for Program memory and Data Memory. Program memory can only be read, not written to. It can be up to 2K bytes of Program memory. Data memory can be read and written to up to 128 bytes including the stack area.
11.1 Registers
This device has six registers that are the Program Counter (PC), a Accumulator (A), two index registers (X, Y), the Stack Pointer (SP), and the Program Status Word (PSW). The Program Counter consists of 16-bit register.
A X Y SP PCH PCL PSW ACCUMULATOR X REGISTER Y REGISTER STACK POINTER PROGRAM COUNTER PROGRAM STATUS WORD
* Stack Pointer The Stack Pointer is an 8-bit register used for occurrence interrupts and calling out subroutines. Stack Pointer identifies the location in the stack to be accessed (save or restore). Generally, SP is automatically updated when a subroutine call is executed or an interrupt is accepted. However, if it is used in excess of the stack area permitted by the data memory allocating configuration, the user-processed data may be lost. The stack can be located at any position within 00H to7FH of the internal data memory. The SP is not initialized by hardware, requiring to write the initial value (the location with which the use of the stack starts) by using the initialization routine. Normally, the initial value of "7FH" is used .
Stack Address ( 000H ~ 07FH ) 15 0 8 7 SP 0
Figure 11-1 Configuration of Registers
* Accumulator The Accumulator is the 8-bit general purpose register, used for data operation such as transfer, temporary saving, and conditional judgement, etc. The Accumulator can be used as a 16-bit register with Y Register as shown below .
Y
Y A
Hardware fixed
Note: The Stack Pointer must be initialized by software because its value is undefined after RESET. Example: To initialize the SP LDX #07FH TXSP ; SP 7FH
A
Two 8-bit Registers can be used as a "YA" 16-bit Register
* Program Counter The Program Counter is a 16-bit wide which consists of two 8-bit registers, PCH and PCL. This counter indicates the address of the next instruction to be executed. In reset state, the program counter has reset routine address (PCH:0FFH, PCL:0FEH). * Program Status Word The Program Status Word (PSW) contains several bits that reflect the current state of the CPU. The PSW is described in Figure 11-3 . It contains the Negative flag, the Overflow flag, the Break flag the Half Carry (for BCD operation), the Interrupt enable flag, the Zero flag, and the Carry flag.
Figure 11-2 Configuration of YA 16-bit Register
* X, Y Registers In the addressing mode which uses these index registers, the register contents are added to the specified address, which becomes the actual address. These modes are extremely effective for referencing subroutine tables and memory tables. The index registers also have increment, decrement, comparison and data transfer functions, and they can be used as simple accumulators.
22
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
[Carry flag C] This flag stores any carry or borrow from the ALU of CPU after an arithmetic operation and is also changed by the Shift Instruction or Rotate Instruction.
[Zero flag Z] This flag is set when the result of an arithmetic operation or data transfer is "0" and is cleared by any other result.
MSB PSW NEGATIVE FLAG OVERFLOW FLAG BRK FLAG
LSB
N
V
-
B
H
I
Z
C
RESET VALUE : 00H CARRY FLAG RECEIVES CARRY OUT ZERO FLAG INTERRUPT ENABLE FLAG HALF CARRY FLAG RECEIVES CARRY OUT FROM BIT 1 OF ADDITION OPERLANDS
Figure 11-3 PSW (Program Status Word) Register
[Interrupt disable flag I] This flag enables/disables all interrupts except interrupt caused by Reset or software BRK instruction. All interrupts are disabled when cleared to "0". This flag immediately becomes "0" when an interrupt is served. It is set by the EI instruction and cleared by the DI instruction. [Half carry flag H] After operation, this is set when there is a carry from bit 3 of ALU or there is no borrow from bit 4 of ALU. This bit can not be set or cleared except CLRV instruction with Overflow flag (V). [Break flag B] This flag is set by software BRK instruction to distinguish BRK from TCALL instruction with the same vector ad-
dress. [Overflow flag V] This flag is set to "1" when an overflow occurs as the result of an arithmetic operation involving signs. An overflow occurs when the result of an addition or subtraction exceeds +127(7FH ) or -128(80H ). The CLRV instruction clears the overflow flag. There is no set instruction. When the BIT instruction is executed, bit 6 of memory is copied to this flag. [Negative flag N] This flag is set to match the sign bit (bit 7) status of the result of a data or arithmetic operation. When the BIT instruction is executed, bit 7 of memory is copied to this flag.
Oct. 1999 ver 1.0
23
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
11.2 Program Memory
A 16-bit program counter is capable of addressing up to 64K bytes, but this device has 2K bytes program memory space only the physically implemented. Accessing a location above FFFFH will cause a wrap-around to 0000H. Figure 11-5 shows a map of the upper part of the Program Memory. After reset, the CPU begins execution from reset vector which is stored in address FFFEH, FFFFH. As shown in Figure 11-5, each area is assigned a fixed location in Program Memory. Program Memory area contains the user program, Page Call (PCALL) area contains subroutine program, to reduce program byte length because of using by 2 bytes PCALL instead of 3 bytes CALL instruction. If it is frequently called, more useful to save program byte length.
0F50H DEVICE CONFIGURATION AREA 0FF0H NOT USED F800H ID ID ID ID ID ID ID PROGRAM MEMORY ID ID ID CONFIG FEFFH FF00H PCALL AREA FFBFH FFC0H FFDFH FFE0H TCALL AREA INTERRUPT VECTOR AREA FFFFH 0F50H 0F60H 0F70H 0F80H 0F90H 0FA0H 0FB0H 0FC0H 0FD0H 0FE0H 0FF0H
spaced at 2-byte interval : FFC0H for TCALL15, FFC2H for TCALL14, etc. The interrupt causes the CPU to jump to specific location, where it commences execution of the service routine. The External interrupt 0, for example, is assigned to location FFFAH. The interrupt service locations are spaced at 2byte interval : FFF8H for External Interrupt 1, FFFAH for External Interrupt 0, etc.
Address FFC0H FFC2H FFC4H FFC6H FFC8H FFCAH FFCCH FFCEH FFD0H FFD2H FFD4H FFD6H FFD8H FFDAH FFDCH FFDEH TCALL Name TCALL15 TCALL14 TCALL13 TCALL12 TCALL11 TCALL10 TCALL9 TCALL8 TCALL7 TCALL6 TCALL5 TCALL4 TCALL3 TCALL2 TCALL1 TCALL0 / BRK 1
Table 11-1 TCALL Vectors
1. The BRK software interrupt is using same address with TCALL0.
As for the area from FF00H to FFFFH, if any area of them is not going to be used, its service location is available as general purpose Program Memory.
Address FFE0H FFE2H FFE4H FFE6H FFE8H FFEAH FFECH FFEEH FFF0H FFF2H FFF4H FFF6H FFF8H FFFAH FFFCH FFFEH Vector Name Not Used Not Used Not Used Basic Interval Timer Watchdog Timer A/D Converter Not Used Not Used Not Used Not Used Timer / Counter 1 Timer / Counter 0 External Interrupt 1 External Interrupt 0 Not Used RESET
Figure 11-4 Program Memory Map
The Device Configuration Area can be programmed or left unprogrammed to select device configuration such as RC oscillation option. This area is not accessible during normal execution but is readable and writable during program / verify. More detail informations are explained in device configuration area section. Table Call (TCALL) causes the CPU to jump to each TCALL address, where it commences execution of the service routine. The Table Call service locations are
Table 11-2 Interrupt Vectors
Page Call (PCALL) area contains subroutine program to
24
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
reduce program byte length by using 2 bytes PCALL instead of 3 bytes CALL instruction. If it is frequently called, it is more useful to save program byte length. Table Call (TCALL) causes the CPU to jump to each TCALL address, where it commences the execution of the service routine. The Table Call service area spaces 2-byte for every TCALL: 0FFC0H for TCALL15, 0FFC2H for TCALL14, etc., as shown in Figure 11-5 .
Example: Usage of TCALL
LDA #5 TCALL 0FH : : ;1BYTE INSTRUCTION ;INSTEAD OF 3 BYTES ;NORM AL CALL
; ;TABLE CALL ROUTINE ; FUNC_A: LDA LRG0 RET ; FUNC_B: LDA LRG1 2 RET ; ;TABLE CALL ADD. AREA ; ORG 0FFC0H DW FUNC_A DW FUNC_B
1
;TCALL ADDRESS AREA
Address 0FFC0H C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF
Program Memory TCALL 15 TCALL 14 TCALL 13 TCALL 12 TCALL 11 TCALL 10 TCALL 9 TCALL 8 TCALL 7 TCALL 6 TCALL 5 TCALL 4 TCALL 3 TCALL 2 TCALL 1 TCALL 0 / BRK *
Address 0FF00H
PCALL Area Memory
PCALL Area (256 Bytes)
0FFFFH
NOTE: * means that the BRK software interrupt is using same address with TCALL0.
Figure 11-5 PCALL and TCALL Memory Area
Oct. 1999 ver 1.0
25
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
PCALL rel
4F35 PCALL 35H
TCALL n
4A TCALL 4
4F 35
4A
01001010
~ ~ ~ ~
0FF00H 0FF35H NEXT
~ ~
NEXT
Reverse
~ ~
0F125H
PC: 11111111 11010110 FH FH D H 6H
0FF00H 0FFD6H 0FFD7H 0FFFFH 25 F1
0FFFFH
Example: The usage software example of Vector address and the initialize part.
ORG DW DW DW DW DW DW DW DW DW DW DW DW DW DW DW DW ORG 0FFE0H NOT_USED NOT_USED NOT_USED BIT_INT WDT_INT AD_INT NOT_USED NOT_USED NOT_USED NOT_USED TMR1_INT TMR0_INT INT1 INT0 NOT_USED RESET 0F800H ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; (0FFEO) (0FFE2) (0FFE4) (0FFE6) (0FFE8) (0FFEA) (0FFEC) (0FFEE) (0FFF0) (0FFF2) (0FFF4) (0FFF6) (0FFF8) (0FFFA) (0FFFC) (0FFFE)
Basic Interval Timer Watchdog Timer A/D
Timer-1 Timer-0 Int.1 Int.0 Reset
;******************************************** ; MAIN PROGRAM * ;******************************************** ; RESET: DI ;Disable All Interrupts LDX #0 RAM_CLR: LDA #0 ;RAM Clear(!0000H->!007FH) STA {X}+ CMPX #080H BNE RAM_CLR ; LDX #07FH ;Stack Pointer Initialize TXSP ; CALL INITIAL ; ; LDM RA, #0 ;Normal Port A LDM RAIO,#1000_0010B ;Normal Port Direction LDM RB, #0 ;Normal Port B LDM RBIO,#1000_0010B ;Normal Port Direction : : LDM PFDR,#0 ;Enable Power Fail Detector :
26
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
11.3 Data Memory
Figure 11-6 shows the internal Data Memory space available. Data Memory is divided into two groups, a user RAM(including Stack) and control registers.
Address C0H C1H C2H C3H C4H C5H CAH CBH CCH D0H D1H D1H D1H D2H D3H D3H D4H D4H D4H D5H DEH E2H E3H E4H E5H E6H EAH EBH ECH ECH EDH EFH
Symbol RA RAIO RB RBIO RC RCIO RAFUNC RBFUNC PUPSEL TM0 T0 TDR0 CDR0 TM1 TDR1 T1PPR T1 CDR1 T1PDR PWMHR BUR IENH IENL IRQH IRQL IEDS ADCM ADCR BITR CKCTLR WDTR PFDR
R/W R/W W R/W W R/W W W W W R/W R W R R/W W W R R R/W W W R/W R/W R/W R/W R/W R/W R R W R/W R/W
RESET Value Undefined 0000_0000 Undefined ---0_0000 Undefined ----_--00 0000_0000 ---0_0000 ----_--00 --00_0000 0000_0000 1111_1111 0000_0000 0000_0000 1111_1111 1111_1111 0000_0000 0000_0000 0000_0000 ----_0000 1111_1111 0000_---000-_---0000_---000-_-------_0000 --00_0001 Undefined 0000_0000 -001_0111 0111_1111 ----_-100
00H
DATA MEMORY (including STACK)
7FH
C0H
CONTROL REGISTERS
FFH
Figure 11-6 Data Memory Map
Internal Data Memory addresses are always one byte wide, which implies an address space of 128 bytes including the stack area. The stack pointer should be initialized within 00 H to 7FH by software because its value is undefined after RESET. The Stack area is defined at the Data Memory area, so the stack should not be overlapped by manipulating RAM Data. For example, we assumed the Stack pointer is 6F. If this address is accessed by program, the stack value is changed. So the malfunction is occurred. The control registers are used by CPU and Peripheral functions for controlling the desired operation of the device. Therefore these registers contain control and status bits for the interrupt system, the timer/ counters, analog to digital converters, I/O ports. The control registers are in address C0H to FFH. Note that unoccupied addresses may not be implemented on the chip. Read accesses to these addresses will in general return random data, and write accesses will have an indeterminate effect. More detail informations of each register are explained in each peripheral sections.
Note: Write only registers can not be accessed by bit manipulation instruction. Do not use read-modify-write instruction. Use byte manipulation instruction.
Table 11-3 RESET Value of Control Registers
Note: Several names are given at same address. Refer to below table.
When read Addr. D1H D3H D4H ECH T1
Timer Mode Capture Mode PWM Mode
When write
Timer Mode PWM Mode
T0
CDR0 CDR1 BITR
-
TDR0 TDR1
T1PPR T1PDR
T1PDR
-
CKCTLR
Example; To write at CKCTLR
LDM
Table 11-4 Various Register Name in Same Adress
CKCTLR,#09H ;Divide ratio /16
Oct. 1999 ver 1.0
27
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
Stack Area The stack provides the area where the return address is saved before a jump is performed during the processing routine at the execution of a subroutine call instruction or the acceptance of an interrupt. When returning from the processing routine, executing the subroutine return instruction [RET] restores the contents of the program counter from the stack; executing the interrupt
return instruction [RETI] restores the contents of the program counter and flags. The save/restore locations in the stack are determined by the stack pointed (SP). The SP is automatically decreased after the saving, and increased before the restoring. This means the value of the SP indicates the stack location number for the next save.
28
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
Address C0H C1H C2H C3H C4H C5H CAH CBH CCH D0H D1H D2H D3H D4H D5H DEH E2H E3H E4H E5H E6H EAH EBH ECH ECH EDH EFH RA
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
RA Port Data Register RA Port Direction Register RB Port Data Register RB Port Direction Register RC Port Data Register RC Port Direction Register ANSEL7 ANSEL6 ANSEL5 CAP0 ANSEL4 PWMO T0CK2 ANSEL3 INT1I T0CK1 ANSEL2 INT0I T0CK0 ANSEL1 BUZO ANSEL0 AVREFS
RAIO RB RBIO RC RCIO RAFUNC RBFUNC PUPSEL TM0 T0/TDR0/ CDR0 TM1 TDR1/ T1PPR T1/CDR1/ T1PDR PWMHR BUR IENH IENL IRQH IRQL IEDS ADCM ADCR BITR1 CKCTLR
Note1
PUPSEL1 PUPSEL0 T0CN T0ST
Timer0 Register / Timer Data Register 0 / Capture Data Register 0 POL 16BIT PWME CAP1 T1CK1 T1CK0 T1CN T1ST
Timer Data Register 1/ PWM Period Register 1 Timer1 Register / Capture Data Register 1 / PWM Duty Register 1 PWM High Register BUCK1 INT0E ADE INT0IF ADIF BUCK0 INT1E WDTE INT1IF WDTIF BUR5 T0E BITE T0IF BITIF ADEN BUR4 T1E T1IF ADS2 BUR3 IED1H ADS1 BUR2 IED1L ADS0 BUR1 IED0H ADST BUR0 IED0L ADSF
ADC Result Data Register Basic Interval Timer Data Register WDTCL WAKEUP RCWDT WDTON BTCL BTS2 BTS1 BTS0
WDTR PFDR2
7-bit Watchdog Counter Register PFDIS PFDM PFDS
Table 11-5 Control Registers of GMS87C1202
These registers of shaded area can not be accessed by bit manipulation instruction as "SET1, CLR1", so should be accessed by register operation instruction as "LDM dp,#imm". 1. 2. The register BITR and CKCTLR are located at same address. Address ECH is read as BITR, written to CKCTLR. The register PFDR only be implemented on devices, not on In-circuit Emulator.
Oct. 1999 ver 1.0
29
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
11.4 Addressing Mode
The GMS87C1201 and GMS87C1202 use six addressing modes. * Register addressing * Immediate addressing * Direct page addressing * Absolute addressing * Indexed addressing
~ ~ ~ ~
C5 35 0035H data
(3) Direct Page Addressing dp In this mode, a address is specified within direct page. Example;
C535 LDA 35H ;A RAM[35H]

data A
* Register-indirect addressing Below example is shown for GMS87C1202. (1) Register Addressing Register addressing accesses the A, X, Y, C and PSW. (2) Immediate Addressing #imm In this mode, second byte (operand) is accessed as a data immediately. Example:
0435 ADC #35H
MEMORY
0F850H 0F851H
(4) Absolute Addressing !abs Absolute addressing sets corresponding memory data to Data , i.e. second byte(Operand I) of command becomes lower level address and third byte (Operand II) becomes upper level address. With 3 bytes command, it is possible to access to whole memory area. ADC, AND, CMP, CMPX, CMPY, EOR, LDA, LDX, LDY, OR, SBC, STA, STX, STY
04 35
A+35H+C A
Example;
0735F0 ADC !0F035H ;A ROM[0F035H]
0F035H
data
~ ~
E45535
LDM
35H,#55H ~ ~
0F900H 0F901H 0F902H 07 35 F0 address: 0F035
A+data+C A
0035H
data
data 55H
0F900H 0F901H 0F902H
~ ~
E4 55 35
~ ~
30
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
The operation within data memory (RAM) ASL, BIT, DEC, INC, LSR, ROL, ROR Example; Addressing accesses the address 0035H .
983500 INC !0035H ;A RAM[035H]
X indexed direct page, auto increment {X}+ In this mode, a address is specified within direct page by the X register and the content of X is increased by 1. LDA, STA Example; X=35H
DB LDA {X}+
0035H
data
~ ~
~ ~
0FA00H 0FA01H 0FA02H 98 35 00

data+1 data
35H
data
~ ~
data A
address: 0035
~ ~
DB
36H X
(5) Indexed Addressing X indexed direct page (no offset) {X} In this mode, a address is specified by the X register. ADC, AND, CMP, EOR, LDA, OR, SBC, STA, XMA Example; X=15H
D4 LDA {X} ;ACCRAM[X].
X indexed direct page (8 bit offset) dp+X This address value is the second byte (Operand) of command plus the data of -register. And it assigns the memory in Direct page. ADC, AND, CMP, EOR, LDA, LDY, OR, SBC, STA STY, XMA, ASL, DEC, INC, LSR, ROL, ROR Example; X=015H
15H
data
C645
LDA
45H+X
~ ~
data A
~ ~
0FA50H D4
5AH data
~ ~
0FB50H 0FB51H C6 45
~ ~

45H+15H=5AH
data A
Oct. 1999 ver 1.0
31
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
Y indexed direct page (8 bit offset) dp+Y This address value is the second byte (Operand) of command plus the data of Y-register, which assigns Memory in Direct page. This is same with above (2). Use Y register instead of X. Y indexed absolute !abs+Y Sets the value of 16-bit absolute address plus Y-register data as Memory. This addressing mode can specify memory in whole area. Example; Y=55H
D500FA LDA !0FA00H+Y
3F35
JMP
[35H]
35H 36H
0A FC
~ ~
0FC0AH NEXT
~ ~
jump to address 0FC0AH
~ ~
0FD00H 3F 35
~ ~
0F900H 0F901H 0F902H
D5 00 FA
0FA00H+55H=0FA55H
X indexed indirect [dp+X] Processes memory data as Data, assigned by 16-bit pair memory which is determined by pair data [dp+X+1][dp+X] Operand plusX-register data in Direct page. ADC, AND, CMP, EOR, LDA, OR, SBC, STA Example; X=10H
1625 ADC [25H+X]
~ ~
0FA55H data
~ ~

data A
(6) Indirect Addressing Direct page indirect [dp] Assigns data address to use for accomplishing command which sets memory data(or pair memory) by Operand. Also index can be used with Index register X,Y. JMP, CALL Example;
0FA00H 35H 36H 05 F9
~ ~
0F905H data
~ 0F905H ~
25 + X(10) = 35H
~ ~
~ ~
16 25
A + data + C A
32
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
Y indexed indirect [dp]+Y Processes momory data as Data, assigned by the data [dp+1][dp] of 16-bit pair memory paired by Operand in Direct pageplus Y-register data. ADC, AND, CMP, EOR, LDA, OR, SBC, STA Example; Y=10H
1725 ADC [25H]+Y
Absolute indirect [!abs] The program jumps to address specified by 16-bit absolute address. JMP Example;
1F25F9 JMP [!0F925H]
PROGRAM MEMORY
25H 26H
05 F8
0F925H 0F926H
E1 F9
~ ~
0F815H data
~ ~
0F805H + Y(10) = 0F815H
~ ~
~ ~
NEXT
jump to address 0F9E1H
~ ~
0F9E1H
~ ~
0FA00H 17 25
~ ~
0FA00H 1F 25 F9
~ ~
A + data + C A
Oct. 1999 ver 1.0
33
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
12. I/O PORTS
The GMS87C1202 has three ports, RA, RB and RC. These ports pins may be multiplexed with an alternate function for the peripheral features on the device. In general, when a initial reset state, all ports are used as a general purpose input port. All pins have data direction registers which can set these ports as output or input. A "1" in the port direction register defines the corresponding port pin as output. Conversely, write "0" to the corresponding bit to specify as an input pin. For example, to use the even numbered bit of RA as output ports and the odd numbered bits as input ports, write "55H" to address C1H (RA direction register) during initial setting as shown in Figure 12-1. Reading data register reads the status of the pins whereas writing to it will write to the port latch.
WRITE "55H" TO PORT RA DIRECTION REGISTER
C0H C1H C2H C3H
RA DATA RA DIRECTION RB DATA RB DIRECTION
01010101 76543210
BIT
I
O
I
O
IO
I
O
7 6 5 4 3 2 1 0 PORT I : INPUT PORT O : OUTPUT PORT
Figure 12-1 Example of port I/O assignment
12.1 RA and RAIO registers
RA is an 8-bit bidirectional I/O port (address C0H). Each port can be set individually as input and output through the RAIO register (address C1H). RA7~RA1 ports are multiplexed with Analog Input Port ( AN7~AN1 ) and RA0 port is multiplexed with Event Counter Input Port ( EC0 ).
RA Data Register RA ADDRESS : C0H RESET VALUE : Undefined
may be used as general I/O ports. To select alternate function such as Analog Input or External Event Counter Input, write "1" to the corresponding bit of RAFUNC.Regardless of the direction register RAIO, RAFUNC is selected to use as alternate functions, port pin can be used as a corresponding alternate features ( RA0/EC0 is controlled by RBFUNC )
PORT RA7/AN7 RAFUNC.7~0 Description
RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0
INPUT / OUTPUT DATA
0 1 0
RA6/AN6
RA7 ( Normal I/O Port ) AN7 ( ADS2~0=111 ) RA6 ( Normal I/O Port ) AN6 ( ADS2~0=110 ) RA5 ( Normal I/O Port ) AN5 ( ADS2~0=101 ) RA4 ( Normal I/O Port ) AN4 ( ADS2~0=100 ) RA3 ( Normal I/O Port ) AN3 ( ADS2~0=011 ) RA2 ( Normal I/O Port ) AN2 ( ADS2~0=010 ) RA1 ( Normal I/O Port ) AN1 ( ADS2~0=001 ) RA0 ( Normal I/O Port ) EC0 ( T0CK2~0=111 )
RA Direction Register RAIO
ADDRESS : C1H RESET VALUE : 00000000
1 0
RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0 RA5/AN5
DIRECTION SELECT 0 : INPUT PORT 1 : OUTPUT PORT
1 0
RA4/AN4
1 0
RA Function Selection Register RAFUNC
ADDRESS : CAH RESET VALUE : 00000000
RA3/AN3
1 0
RA2/AN2
ANSEL7 ANSEL6 ANSEL5 ANSEL4 ANSEL3 ANSEL2 ANSEL1 ANSEL0
0 : RA4 1 : AN4 0 : RA5 1 : AN5 0 : RA6 1 : AN6 0 : RA7 1 : AN7
0 : RB0 1 : AN0 0 : RA1 1 : AN1 0 : RA2 1 : AN2 0 : RA3 1 : AN3
1 0
RA1/AN1
1
RA0/EC01
Figure 12-2 Registers of Port RA
The control register RAFUNC (address CAH) controls to select alternate function. After reset, this value is "0", port
1. This port is not an Analog Input port, but Event Counter clock source input port. ECO is controlled by setting TOCK2~0 = 111. The bit RAFUNC.0 (ANSEL0) controls the RB0/AN0/AVref port ( Refer to Port RB).
34
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
12.2 RB and RBIO registers
RB is a 5-bit bidirectional I/O port (address C2H). Each pin can be set individually as input and output through the
RB Data Register RB ADDRESS : C2H RESET VALUE : Undefined
RBIO register (address C3H).
Pull-up Selection Register PUPSEL
-
ADDRESS : CCH RESET VALUE : ------00
PUP1 PUP0
RB4 RB3 R B 2
RB1 RB0
INPUT / OUTPUT DATA RB Direction Register RBIO ADDRESS : C3H RESET VALUE : ---00000
RB3 / INT1 Pull-up 0 : No Pull-up 1 : With Pull-up
RB2 / INT0 Pull-up 0 : No Pull-up 1 : With Pull-up
Interrupt Edge Selection Register IEDS ADDRESS : E6H RESET VALUE : ----0000
IED1H IED1L IED0H IED0L
-
-
-
RB4 RB3 RB2 RB1 RB0
DIRECTION SELECT 0 : INPUT PORT 1 : OUTPUT PORT
INT1
INT0
External Interrupt Edge Select RB Function Selection Register RBFUNC
PWMO INT1I
ADDRESS : CBH RESET VALUE : ---00000
INT0I BUZO AVREFS
00 : Normal I/O port 01 : Falling ( 1-to-0 transition ) 10 : Rising ( 0-to-1 transition ) 11 : Both ( Rising & Falling ) 0 : RB0 when ANSEL0 = 0, AN0 when ANSEL0 = 1 1 : AVref
0 : RB4 1 : PWM0 Output or Compare Output
0 : RB3 1 : INT1
0 : RB2 1 : INT0
0 : RB1 1 : BUZ Output
The shaded areas are only related with in GMS87C1202/1201. So in GMS87C1102/1101, this area must be written to "0".
Figure 12-3 Registers of Port RB
In addition, Port RB is multiplexed with various special features. The control register RBFUNC (address CB H) controls to select alternate function. After reset, this value is "0", port may be used as general I/O ports. To select alternate function such as External interrupt or Timer compare output, write "1" to the corresponding bit of RBFUNC. Regardless of the direction register RBIO, RBFUNC is selected to use as alternate functions, port pin can be used as a corresponding alternate features.
PORT
RBFUNC.4~0
Description
RB4/ PWM0/ COMP0 RB3/INT1
0 1 0 1 0 1 0 1 01 12
RB4 ( Normal I/O Port ) PWM0 Output / Timer1 Compare Output RB3 ( Normal I/O Port ) External Interrupt Input 1 RB2 ( Normal I/O Port ) External Interrupt Input 0 RB1 ( Normal I/O Port ) Buzzer Output RB0 ( Normal I/O Port ) / AN0 (ANSEL0=1) External Analog Reference Voltage
RB2/INT0
RB1/BUZ
RB0/AN0/ AVref
1. When ANSEL0 = "0", this port is defined for normal I/O port ( RB0 ). When ANSEL0 = "1" and ADS2~0 = " 000", this port can be used Analog Input Port ( AN0 ). 2. When this bit set to "1", this port defined for AVref , so it can not be used Analog Input Port AN0 and Normal I/O Port RB0.
Oct. 1999 ver 1.0
35
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
12.3 RC and RCIO registers
RC is an 4-bit bidirectional I/O port (address C4H). Each pin can be set individually as input and output through the RCIO register (address C5H).
RC Data Register RC
ADDRESS : C4H RESET VALUE : Undefined
RC Direction Register RCIO
ADDRESS : C5H RESET VALUE : ------00
-
-
-
-
-
-
RC1 RC0
-
-
-
-
-
-
RC1 RC0
INPUT / OUTPUT DATA
DIRECTION SELECT 0 : INPUT PORT 1 : OUTPUT PORT
Figure 12-4 Registers of Port RC
36
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
13. CLOCK GENERATOR
The clock generator produces the basic clock pulses which provide the system clock to be supplied to the CPU and peripheral hardware. The main system clock oscillator oscillates with a crystal resonator or a ceramic resonator connected to the
OSCILLATION CIRCUIT fxin
Xin and Xout pins. External clocks can be input to the main system clock oscillator. In this case, input a clock signal to the Xin pin and open the Xout pin
CLOCK PULSE GENERATOR
Internal system clock
PRESCALER STOP WAKEUP
/1
/2
/4
/8
/16
/32
/64
/128
/256
/512
/1024 /2048
Peripheral clock
Figure 13-1 Block Diagram of Clock Pulse Generator
13.1 Oscillation Circuit
XIN and XOUT are the input and output, respectively, a inverting amplifier which can be set for use as an on-chip oscillator, as shown in Figure 13-2 .
Xout R1 Xin Vss OPEN Recommended: C1, C2 = 30pF10pF for Crystals R1 = 1M Xout
ings for timing insensitive applications. The RC oscillator frequency is a function of the supply voltage, the external resistor (Rext) and capacitor (Cext) values, and the operating temperature. The user needs to take into account variation due to tolerance of external R and C components used. Figure 13-4 shows how the RC combination is connected to the GMS87C1202.
C1 C2
Figure 13-2 Oscillator Connections
External Clock Source
Xin Vss
To drive the device from an external clock source, Xout should be left unconnected while Xin is driven as shown in Figure 13-3. There are no requirements on the duty cycle of the external clock signal, since the input to the internal clocking circuitry is through a divide-by-two flip-flop, but minimum and maximum high and low times specified on the data sheet must be observed. Oscillation circuit is designed to be used either with a ceramic resonator or crystal oscillator. Since each crystal and ceramic resonator have their own characteristics, the user should consult the crystal manufacturer for appropriate values of external components In addition, the GMS87C1202 has an ability for the external RC oscillated operation. It offers additional cost sav-
Figure 13-3 External Clock Connections
Note: When using a system clock oscillator, carry out wiring in the broken line area in Figure 13-2 to prevent any effects from wiring capacities. - Minimize the wiring length. - Do not allow wiring to intersect with other signal conductors. - Do not allow wiring to come near changing high current. - Set the potential of the grounding position of the oscillator capacitor to that of VSS. Do not ground to any ground pattern where high current is present. - Do not fetch signals from the oscillator.
Oct. 1999 ver 1.0
37
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
Vdd Rext Xin Cext
Note: When using a system clock oscillator, carry out wiring in the broken line area in Figure 13-2 to prevent any effects from wiring capacities.
- Minimize the wiring length. - Do not allow wiring to intersect with other signal
conductors.
fxin/4
Xout
Figure 13-4 RC Oscillator Connections
The oscillator frequency, divided by 4, is output from the Xout pin, and can be used for test purpose or to synchroze other logic. To set the RC oscillation, it should be programmed RCOPT bit to "1" to CONFIG (0FF0H). ( Refer to DEVICE CONFIGURATION AREA )
- Do not allow wiring to come near changing high current. - Set the potential of the grounding position of the oscillator capacitor to that of VSS. Do not ground to any ground pattern where high current is present.
- Do not fetch signals from the oscillator.
38
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
14. Basic Interval Timer
The GMS87C1202 has one 8-bit Basic Interval Timer that is free-run, can not stop. Block diagram is shown in Figure 14-1 .The 8-bit Basic interval timer register (BITR) is increased every internal count pulse which is divided by prescaler. Since prescaler has divided ratio by 8 to 1024, the count rate is 1/8 to 1/1024 of the oscillator frequency. As the count overflows from FFH to 00H, this overflow causes to generate the Basic interval timer interrupt. The BITF is interrupt request flag of Basic interval timer. When write "1" to bit BTCL of CKCTLR, BITR register is cleared to "0" and restart to count-up. The bit BTCL becomes "0" after one machine cycle by hardware. If the STOP instruction executed after writing "1" to bit WAKEUP of CKCTLR, it goes into the wake-up timer mode. In this mode, all of the block is halted except the oscillator, prescaler ( only fxin/2048 ) and Timer0.
WAKEUP RCWDT STOP BTS[2:0]
If the STOP instruction executed after writing "1" to bit RCWDT of CKCTLR, it goes into the internal RC oscillated watchdog timer mode. In this mode, all of the block is halted except the internal RC oscillator, Basic Interval Timer and Watchdog Timer. More detail informations are explained in Power Saving Function. The bit WDTON decides Watchdog Timer or the normal 7-bit timer
Note: All control bits of Basic interval timer are in CKCTLR register which is located at same address of BITR (address ECH). Address ECH is read as BITR, written to CKCTLR. Therefore, the CKCTLR can not be accessed by bit manipulation instruction.
.
fxin
/8 / 16 / 32 / 64 / 128 / 256 / 512 / 1024
3
BTCL Clear
To Watchdog Timer
8 MUX
0 BITR (8BIT) 1 BITIF
Basic Interval Timer Interrupt
Internal RC OSC
Figure 14-1 Block Diagram of Basic Interval Timer
Clock Control Register CKCTLR WAKEUP RCWDT WDTON BTCL BTS2 BTS1 BTS0 ADDRESS : ECH RESET VALUE : -0010111 Bit Manipulation Not Available
Basic Interval Timer Clock Selection Symbol WAKEUP RCWDT WDTON BTCL Function Description 1: Enables Wake-up Timer 0: Disables Wake-up Timer 1: Enables Internal RC Watchdog Timer 0: Disables Internal RC Watchdog Time 1: Enables Watchdog Timer 0: Operates as a 7-bit Timer 1: BITR is cleared and BTCL becomes "0" automatically after one machine cycle, and BITR continue to count-up 001 : fxin / 16 010 : fxin / 32 011 : fxin / 64 100 : fxin / 128 101 : fxin / 256 110 : fxin / 512 111 : fxin / 1024 000 : fxin / 8
Figure 14-2 CKCTLR : Clock Control Register
Oct. 1999 ver 1.0
39
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
15. TIMER / COUNTER
The GMS87C1202 has two Timer/Counter registers. Each module can generate an interrupt to indicate that an event has occurred (i.e. timer match). Timer 0 and Timer 1 can be used either the two 8-bit Timer/Counter or one 16-bit Timer/Counter by combining them. In the "timer" function, the register is increased every internal clock input. Thus, one can think of it as counting internal clock input. Since a least clock consists of 2 and most clock consists of 2048 oscillator periods, the count rate is 1/2 to 1/2048 of the oscillator frequency in Timer0. And Timer1 can use the same clock source too. In addition, Timer1 has more fast clock source ( 1/1 to 1/8 ). In the "counter" function, the register is increased in response to a 0-to-1 (rising edge) transition at its corresponding external input pin, EC0. And in the "capture" function, the register is increased in response external interrupt same with timer function. When external interrupt edge input, the count register is captured into capture data register CDRx. Timer1 is shared with "PWM" function and "Compare output" function It has seven operating modes: "8-bit timer/counter", "16bit timer/counter", "8-bit capture", "16-bit capture", "8-bit compare output", "16-bit compare output" and "10-bit PWM" which are selected by bit in Timer mode register TM0 and TM1 as shown in Figure 15-1 and Table 15-1.
Timer 0 Mode Register TM0 CAP0 T0CK2 T0CK1 T0CK0 T0CN T0ST ADDRESS : D0H RESET VALUE : --000000
CAP0
Capture mode selection bit. 0 : Disables Capture 1 : Enables Capture Input clock selection 000 : fxin / 2 100 : fxin / 128 101 : fxin / 512 110 : fxin / 2048 111 : External Event ( EC0 )
T0CN
Continue control bit 0 : Stop counting 1 : Start counting continuously Start control bit 0 : Stop counting 1 : Counter register is cleared and started again
T0CK[2:0]
T0ST
001 : fxin / 4 010 : fxin / 8
011 : fxin / 32 Timer 1 Mode Register TM1 POL 16BIT
PWME
CAP1
T1CK1
T1CK0
T1CN
T1ST
ADDRESS : D2H RESET VALUE : 00000000
POL
PWM Output Polarity 0 : Duty active low 1 : Duty active high 16-bit mode selection 0 : 8-bit mode 1 : 16-bit mode PWM enable bit 0 : Disables PWM 1 : Enables PWM Capture mode selection bit. 0 : Disables Capture 1 : Enables Capture
T1CK[2:0]
01 : fxin / 2 T1CN
Input clock selection 00 : fxin 10 : fxin / 8 11 : using the Timer 0 clock
16BIT
Continue control bit 0 : Stop counting 1 : Start counting continuously Start control bit 0 : Stop counting 1 : Counter register is cleared and started again
PWME
T1ST
CAP1
Figure 15-1 Timer 0 and Timer 1 Mode Register
40
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
16BIT 0 0 0 0 1 1 1 1
CAP0 0 0 1 0 0 0 1 0
CAP1 0 1 0 0 0 0 X2 0
PWME 0 0 0 1 0 0 0 0
T0CK[2:0] XXX 111 XXX XXX XXX 111 XXX XXX
T1CK[1:0] XX XX XX XX 11 11 11 11
PWMO1 0 0 1 1 0 0 0 1
TIMER 0 8-bit Timer 8-bit Event Counter 8-bit Capture 8-bit Timer/Counter 16-bit Timer 16-bit Event Counter 16-bit Capture 16-bit Compare output
TIMER1 8-bit Timer 8-bit Capture 8-bit Compare output 10-bit PWM
Table 15-1 Operating Modes of Timer 0 and Timer 1
1. 2. This bit is the bit4 of RB Function register(RBFUNC). X : The value is "0" or "1" corresponding your operation.
15.1 8-bit Timer/Counter Mode
The GMS87C1202 has two 8-bit Timer/Counters, Timer 0 and Timer 1, as shown in Figure 15-2 . The "timer" or "counter" function is selected by mode registers TM0, TM1 as shown in Figure 15-1 and Table 15-1 . To use as an 8-bit timer/counter mode, bit CAP0 of TM0 is cleared to "0" and bits 16BIT of TM1 should be cleared to "0"(Table 15-1).
TM0
-
16BIT 0
CAP0 0 PWME 0 T0CK[2:0]
T0CK2 X CAP1 0
T0CK1 X T1CK1 X
T0CK0 X T1CK0 X
T0CN X T1CN X
T0ST X T1ST X
ADDRESS : D0H RESET VALUE : --000000
TM1
POL X
ADDRESS : D2H RESET VALUE : 00000000
X : The value "0" or "1" corresponding your operation.
T0ST 0 : Stop 1 : Clear and Start
1
Edge Detector
EC0
fxin
/2 /4 /8 / 32 / 128 / 512 / 2048 /1 /2 /8
MUX
T0 ( 8-bit )
CLEAR
T0IF T0CN TDR0 ( 8-bit ) T1CK[1:0] T1ST 0 : Stop 1 : Clear and Start
1
TIMER 0 INTERRUPT
COMPARATOR
COMP0 PIN F/F
MUX
T1 ( 8-bit )
CLEAR
T1IF T1CN TDR1 ( 8-bit ) COMPARATOR
TIMER 1 INTERRUPT
Figure 15-2 8-bit Timer / Counter Mode
Oct. 1999 ver 1.0
41
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
These timers have each 8-bit count register and data register. The count register is increased by every internal or external clock input. The internal clock has a prescaler divide ratio option of 2, 4, 8, 32,128, 512, 2048 (selected by control bits T0CK2, T0CK1 and T0CK0 of register TM0) and 1, 2, 8 (selected by control bits T1CK1 and T1CK0 of register TM1). In the Timer 0, timer register T0 increases from 00H until it matches TDR0 and then reset to 00H. The match output of Timer 0 generates Timer 0 interrupt
(latched in T0F bit). As TDRx and Tx register are in same address, when reading it as a Tx, written to TDRx. In counter function, the counter is increased every 0-to 1 (rising edge) transition of EC0 pin. In order to use counter function, the bit RA0 of the RA Direction Register RAIO is set to "0". The Timer 0 can be used as a counter by pin EC0 input, but Timer 1 can not.
TDR1
n n-1
up -c ou nt
9 8 7 6
PCP
~ ~
~ ~
~ ~
2 1 0
5 4 3
TIME
Interrupt period = PCP x (n+1)
Timer 1 (T1IF) Interrupt
interrupt occurs
interrupt occurs
interrupt occurs
Figure 15-3 Counting Example of Timer Data Registers
TDR1
disable enable
clear & start stop
up -c ou nt
~ ~
~ ~
TIME Timer 1 (T1IF) Interrupt
interrupt occurs interrupt occurs
T1ST Start & Stop
T1ST = 0
T1ST = 1
T1CN Control count
T1CN = 0 T1CN = 1
Figure 15-4 Timer Count Operation
42
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
15.2 16-bit Timer/Counter Mode
The Timer register is being run with 16 bits. A 16-bit timer/ counter register T0, T1 are increased from 0000H until it matches TDR0, TDR1 and then resets to 0000 H . The match output generates Timer 0 interrupt not Timer 1 interrupt. The clock source of the Timer 0 is selected either internal or external clock by bit T0CK2, T0CK1 and T0SL0. In 16-bit mode, the bits T1CK1,T1CK0 and 16BIT of TM1 should be set to "1" respectively.
TM0
-
16BIT 1
CAP0 0 PWME 0
T0CK2 X CAP1 0
T0CK1 X T1CK1 1
T0CK0 X T1CK0 1
T0CN X T1CN X
T0ST X T1ST X
ADDRESS : D0H RESET VALUE : --000000
TM1
POL X
ADDRESS : D2H RESET VALUE : 00000000
X : The value "0" or "1" corresponding your operation.
T0CK[2:0] Edge Detector T0ST 0 : Stop 1 : Clear and Start
1
EC0
fxin
/2 /4 /8 / 32 / 128 / 512 / 2048
MUX
T1 ( 8-bit )
T0 ( 8-bit )
CLEAR
T0CN COMPARATOR
T0IF
TIMER 0 INTERRUPT
F/F TDR1 ( 8-bit ) TDR0 ( 8-bit ) COMP0 PIN
Figure 15-5 16-bit Timer / Counter Mode
15.3 8-bit Compare Output ( 16-bit )
The GMS87C1201 and GMS87C1202 has a function of Timer Compare Output. To pulse out, the timer match can goes to port pin( COMP0 ) as shown in Figure 15-2 and Figure 15-5 . Thus, pulse out is generated by the timer match. These operation is implemented to pin, RB4/ COMP0/PWM. This pin output the signal having a 50 : 50 duty square wave, and output frequency is same as below equation.
= ----------------------------------------------------------------------------------------- x
x ( + )
In this mode, the bit PWMO of RB function register (RBFUNC) should be set to "1", and the bit PWME of timer1 mode register ( TM1 ) should be set to "0". In addition, 16-bit Compare output mode is also available.
15.4 8-bit Capture Mode
The Timer 0 capture mode is set by bit CAP0 of timer mode register TM0 (bit CAP1 of timer mode register TM1 for Timer 1) as shown in Figure 15-6. As mentioned above, not only Timer 0 but Timer 1 can also be used as a capture mode. The Timer/Counter register is increased in response internal or external input. This counting function is same with normal timer mode, and Timer interrupt is generated when timer register T0 (T1) increases and matches TDR0 (TDR1).
Oct. 1999 ver 1.0
43
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
This timer interrupt in capture mode is very useful when the pulse width of captured signal is more wider than the maximum period of Timer. For example, in Figure 15-8 , the pulse width of captured signal is wider than the timer data value (FF H ) over 2 times. When external interrupt is occured, the captured value (13H) is more little than wanted value. It can be obtained correct value by counting the number of timer overflow occurence. Timer/Counter still does the above, but with the added feature that a edge transition at external input INTx pin causes the current value in the Timer x register (T0,T1), to be captured into registers CDRx (CDR0, CDR1), respectively.
After captured, Timer x register is cleared and restarts by hardware. It has three transition modes: "falling edge", "rising edge", "both edge" which are selected by interrupt edge selection register IEDS (Refer to External interrupt section). In addition, the transition at INTx pin generate an interrupt.
Note: The CDRx, TDRx and Tx are in same address. In the capture mode, reading operation is read the CDRx, not Tx because path is opened to the CDRx, and TDRx is only for writing operation.
TM0
-
16BIT 0
CAP0 1 PWME 0 T0CK[2:0]
T0CK2 X CAP1 1
T0CK1 X T1CK1 X
T0CK0 X T1CK0 X
T0CN X T1CN X T0ST
T0ST X T1ST X
ADDRESS : D0H RESET VALUE : --000000
TM1
POL X
ADDRESS : D2H RESET VALUE : 00000000
Edge Detector
0 : Stop 1 : Clear and Start
1
EC0
fxin
/2 /4 /8 / 32 / 128 / 512 / 2048
MUX
T0 ( 8-bit )
CLEAR
T0IF T0CN CAPTURE CDR0 ( 8-bit ) COMPARATOR TDR0 ( 8-bit )
TIMER 0 INTERRUPT
INT0IF INT0 IEDS[1:0] T0ST 0 : Stop 1 : Clear and Start CLEAR
INT 0 INTERRUPT
/1 /2 /8
1
MUX
T1 ( 8-bit )
T1IF T1CK[1:0] T1CN IEDS[3:2] CAPTURE INT1IF INT1 INT 1 INTERRUPT CDR1 ( 8-bit ) COMPARATOR TDR1 ( 8-bit )
TIMER 1 INTERRUPT
Figure 15-6 8-bit Capture Mode
44
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
T0
up -c ou nt
n n-1
This value is loaded to CDR0
~ ~
~ ~
9 8 7 6
5 4 3 2 1 0
~ ~
TIME
Ext. INT0 Pin
Interrupt Request ( INT0F ) Interrupt Interval Period
Ext. INT0 Pin
Interrupt Request ( INT0F ) Capture ( Timer Stop )
Delay Clear & Start
Figure 15-7 Input Capture Operation
Ext. INT0 Pin
Interrupt Request ( INT0F ) Interrupt Interval Period = FFH + 01H + FFH +01H + 13H = 213H Interrupt Request ( T0F ) FFH T0 13H 00H 00H FFH
Figure 15-8 Excess Timer Overflow in Capture Mode
Oct. 1999 ver 1.0
45
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
15.5 16-bit Capture Mode
16-bit capture mode is the same as 8-bit capture, except that the Timer register is being run will 16 bits. The clock source of the Timer 0 is selected either internal or external clock by bit T0CK2, T0CK1 and T0CK0.
ADDRESS : D0H RESET VALUE : --000000
In 16-bit mode, the bits T1CK1,T1CK0 and 16BIT of TM1 should be set to "1" respectively.
TM0
-
16BIT 1
CAP0 1 PWME 0
T0CK2 X CAP1 X
T0CK1 X T1CK1 1
T0CK0 X T1CK0 1
T0CN X T1CN X
T0ST X T1ST X
TM1
POL X
ADDRESS : D2H RESET VALUE : 00000000
X : The value "0" or "1" corresponding your operation.
T0CK[2:0] Edge Detector T0ST 0 : Stop 1 : Clear and Start
1
EC0
fxin
/2 /4 /8 / 32 / 128 / 512 / 2048
MUX T0CN
T0 + T1 ( 16-bit )
CLEAR
T0IF COMPARATOR
TIMER 0 INTERRUPT
CAPTURE
CDR1 CDR0 TDR1 TDR0 ( 8-bit ) ( 8-bit ) ( 8-bit ) ( 8-bit ) INT0IF INT 0 INTERRUPT
INT0 IEDS[1:0]
Figure 15-9 16-bit Capture Mode
15.6 PWM Mode
The GMS87C1202 has a two high speed PWM (Pulse Width Modulation) functions which shared with Timer1. In PWM mode, pin RB4/COMP0/PWM0 outputs up to a 10-bit resolution PWM output. This pin should be defined as a PWM output by setting "1" bit PWMO in RBFUNC register. The period of the PWM output is determined by the T1PPR (PWM0 Period Register) and PWM0HR[3:2] (bit3,2 of PWM0 High Register) and the duty of the PWM output is determined by the T1PDR (PWM0 Duty Register) and PWM0HR[1:0] (bit1,0 of PWM0 High Register). The user writes the lower 8-bit period value to the T1PPR and the higher 2-bit period value to the PWM0HR[3:2]. And writes duty value to the T1PDR and the PWM0HR[1:0] same way. The T1PDR is configured as a double buffering for glitchless PWM output. In Figure 15-10 , the duty data is transfered from the master to the slave when the period data matched to the counted value. ( i.e. at the beginning of next duty cycle )
PWM Period = [ PWM0HR[3:2]T1PPR ] X Source Clock PWM Duty = [ PWM0HR[1:0]T1PDR ] X Source Clock
The relation of frequency and resolution is in inverse proportion. Table 15-2 shows the relation of PWM frequency vs. resolution.
46
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
If it needed more higher frequency of PWM, it should be reduced resolution.
Frequency Resolution 10-bit 9-bit 8-bit 7-bit T1CK[1:0] = 00(125nS) 7.8KHz 15.6KHz 31.2KHz 62.5KHz T1CK[1:0] = 01(250nS) 3.9KHz 7.8KHz 15.6KHz 31.2KHz T1CK[1:0] = 10(1uS) 0.98KHZ 1.95KHz 3.90KHz 7.81KHz
determined by the bit POL ( 1: Low, 0: High ). It can be changed duty value when the PWM output. Howerver the changed duty value is output after the current period is over. And it can be maintained the duty value at present output when changed only period value shown as Figure 15-12 . As it were, the absolute duty time is not changed in varying frequency. But the changed period value must greater than the duty value
Note: At PWM output start command, one first pulse would be output abnormally. Because if user writes register values while timer is in operaiton, these register could be set with certain values at first. To prevent this operation, user must stop PWM timer clock and then set the duty and the period register values.
Table 15-2 PWM Frequency vs. Resolution at 8MHz
The bit POL of TM1 decides the polarity of duty cycle. If the duty value is set same to the period value, the PWM output is determined by the bit POL ( 1: High, 0: Low ). And if the duty value is set to "00H", the PWM output is
.
TM1
POL X
16BIT 0 -
PWME 1 -
CAP1 0 -
T1CK1 X
T1CK0 X
T1CN X
T1ST X
ADDRESS : D2H RESET VALUE : 00000000
PWM0HR
-
PWM0HR3PWM0HR2PWM0HR1PWM0HR0 X X X Duty High X
ADDRESS : D5H RESET VALUE : ----0000 Bit Manipulation Not Available
Period High PWM0HR[3:2] T1ST T0 clock source 0 : Stop 1 : Clear and Start T1PPR(8-bit) COMPARATOR
X : The value IS "0" or "1" corresponding your operation.
SQ
1
CLEAR T1 ( 8-bit )
RB4/ PWM0
fxin
/1 /2 /8
MUX
R PWM0O [RBFUNC.4] POL
COMPARATOR T1CK[1:0] T1CN Slave T1PDR(8-bit)
PWM0HR[1:0] Master
T1PDR(8-bit)
Figure 15-10 PWM Mode
Oct. 1999 ver 1.0
47
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
~ ~
~ ~
fxin
~~ ~~
~~~ ~~~
T1 PWM POL=1 PWM POL=0
00 01
02
03
04
05
7F
80
81
3FF
00 01
02
03
Duty Cycle [ 80H x 125nS = 16uS ] Period Cycle [ 3FFH x 125nS = 127.875uS, 7.8KHz ] T1CK[1:0] = 00 ( fxin ) PWM0HR = 0CH T1PPR = FFH T1PDR = 80H
Duty PWM0HR1PWM0HR0 0 0 T1PDR (8-bit) 80H T1PPR (8-bit) FFH
Period PWM0HR3PWM0HR2 1 1
Figure 15-11 Example of PWM at 8MHz
T 1C K [1:0] = 10 ( 1uS ) P W M H R = 00H T 1P P R = 0E H T 1P D R = 05H Source clock T1 PWM POL=1 Duty Cycle [ 05H x 1uS = 5uS ] Period Cycle [ 0EH x 1uS = 14uS, 71KHz ] Duty Cycle [ 05H x 1uS = 5uS ] Duty Cycle [ 05H x 1uS = 5uS ]
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 01 02 03 04 05 06 07 08 09 0A 01 02 03 04 05
Write T1PPR to 0AH
~ ~
~ ~
Period changed Period Cycle [ 0AH x 1uS = 10uS, 100KHz ]
Figure 15-12 Example of Changing the Period in Absolute Duty Cycle (@8MHz)
~ ~
48
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
16. Buzzer Output Function
The buzzer driver consists of 6-bit binary counter, the buzzer register BUR and the clock selector. It generates square-wave which is very wide range frequency (480 Hz~250 KHz at fxin = 4 MHz) by user programmable counter. Pin RB1 is assigned for output port of Buzzer driver by setting the bit BUZO of RBFUNC to "1". The 6-bit buzzer counter is cleared and start the counting by writing signal to the register BUR. It is increased from 00H until it matches 6-bit register BUR. Also, it is cleared by counter overflow and count up to output the square wave pulse of duty 50%. The bit 0 to 5 of BUR determines output frequency for buzzer driving. Frequency calculation is following as shown below.
Oscillator Frequency ( ) = ----------------------------------------------------------------------------------- x Prescaler Ratio x ( + )
The bits BUCK1, BUCK0 of BUR selects the source clock from prescaler output.
BUR
BUCK1
BUCK0
BUR5
BUR4
BUR3
BUR2
BUR1
BUR0
ADDRESS : DEH RESET VALUE : 11111111 Bit Manipulation Not Available
Input clock selection 00 : fxin / 8 01 : fxin / 16
Buzzer Period Data
10 : fxin / 32 11 : fxin / 64
fxin
/8 / 16 / 32 / 64
MUX
COUNTER ( 6-bit )
F/F BUCK[1:0] BUR ( 6-bit ) COMPARATOR RB1/BUZ PIN BUZO [RBFUNC.1]
Figure 16-1 Buzzer Driver
Oct. 1999 ver 1.0
49
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
17. ANALOG TO DIGITAL CONVERTER
The analog-to-digital converter (A/D) allows conversion of an analog input signal to a corresponding 8-bit digital value. The A/D module has eight analog inputs, which are multiplexed into one sample and hold. The output of the sample and hold is the input into the converter, which generates the result via successive approximation. The analog reference voltage is selected to VDD or AVref by setting of the bit AVREFS in RBFUNC register. If external analog reference AVref is selected, the bit ANSEL0 should not be set to "1", because this pin is used to an analog reference of A/D converter. The A/D module has two registers which are the control register ADCM and A/D result register ADCR. The ADCM register, shown in Figure 17-2 , controls the operation of the A/D converter module. The port pins can be configured as analog inputs or digital I/O.
ADS[2:0]
To use analog inputs, each port is assigned analog input port by setting the bit ANSEL[7:0] in RAFUNC register. And selected the corresponding channel to be converted by setting ADS[2:0]. The processing of conversion is start when the start bit ADST is set to "1". After one cycle, it is cleared by hardware. The register ADCR contains the results of the A/D conversion. When the conversion is completed, the result is loaded into the ADCR, the A/D conversion status bit ADSF is set to "1", and the A/D interrupt flag ADIF is set. The block diagram of the A/D module is shown in Figure 17-1. The A/D status bit ADSF is set automatically when A/D conversion is completed, cleared when A/D conversion is in process. The conversion time takes maximum 10 uS (at fxin=8 MHz).
111 RA7/AN7 ANSEL7 110 RA6/AN6 A/D Result Register ANSEL6 101 RA5/AN5 ANSEL5 100 RA4/AN4 ANSEL4 011 RA3/AN3 ANSEL3 010 RA2/AN2 ANSEL2 001 RA1/AN1 ANSEL1 RB0/AN0/AVref 000 Resistor Ladder Circuit Sample & Hold S/H Successive Approximation Circuit ADCR(8-bit) ADDRESS : EBH RESET VALUE : Undefined
A D IF
A/D Interrupt
ANSEL0 ( RAFUNC.0 )
1 VDD Pin 0 ADEN AVREFS ( RBFUNC.0 )
Figure 17-1 A/D Converter Block Diagram
50
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
A/D Control Register ADCM Reserved Analog Channel Select 000 : Channel 0 ( RB0/AN0 ) 001 : Channel 1 ( RA1/AN1 ) 010 : Channel 2 ( RA2/AN2 ) 011 : Channel 3 ( RA3/AN3) 100 : Channel 4 ( RA4/AN4 ) 101 : Channel 5 ( RA5/AN5 ) 110 : Channel 6 ( RA6/AN6 ) 111 : Channel 7 ( RA7/AN7 ) A/D Enable bit 1 : A/D Conversion is enable 0 : A/D Converter module shut off and consumes no operation current A/D Result Data Register ADCR ADCR7 ADCR6 ADCR5 ADCR4 ADCR3 ADCR2 ADCR1 ADCR0 ADDRESS : EBH RESET VALUE : Undefined A/D Status bit 0 : A/D Conversion is in process 1 : A/D Conversion is completed A/D Start bit 1 : A/D Conversion is started After 1 cycle, cleared to "0" 0 : Bit force to zero ADEN ADS2 ADS1 ADS0 ADST ADSF ADDRESS : EAH RESET VALUE : --000001
Figure 17-2 A/D Converter Registers
A/D Converter Cautions (1) Input range of AN0 to AN7
ENABLE A/D CONVERTER
The input voltages of AN0 to AN7 should be within the specification range. In particular, if a voltage above VDD
A/D INPUT CHANNEL SELECT
(or AVref) or below VSS is input (even if within the absolute maximum rating range), the conversion value for that channel can not be indeterminate. The conversion values of the other channels may also be affected.
ANALOG REFERENCE SELECT
(2) Noise countermeasures
In order to maintain 8-bit resolution, attention must be paid to noise on pins AVref(or VDD)and AN0 to AN7. Since the effect
A/D START ( ADST = 1 )
increases in proportion to the output impedance of the analog input source, it is recommended that a capacitor be connected externally as shown in Figure 17-4 in order to reduce noise
NOP
.
ADSF = 1 NO YES 100~1000pF READ ADCR Analog Input AN0~AN7
Figure 17-3 A/D Converter Operation Flow
Figure 17-4 Analog Input Pin Connecting Capacitor
Oct. 1999 ver 1.0
51
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
(3) Pins AN0/RB0 and AN1/RA1 to AN7/RA7 The analog input pins AN0 to AN7 also function as input/ output port (PORT RA and RB0) pins. When A/D conversion is performed with any of pins AN0 to AN7 selected, be sure not to execute a PORT input instruction while conversion is in progress, as this may reduce the conversion resolution. Also, if digital pulses are applied to a pin adjacent to the pin in the process of A/D conversion, the expected A/D conversion value may not be obtainable due to coupling
noise. Therefore, avoid applying pulses to pins adjacent to the pin undergoing A/D conversion.
(4) AVREF pin input impedance A series resistor string of approximately 10K is connected between the AVREFpin and the VSS pin.
Therefore, if the output impedance of the reference voltage source is high, this will result in parallel connection to the
series resistor string between the AVREF pin and the VSS pin, and there will be a large reference voltage error.
52
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
18. INTERRUPTS
The GMS87C1202 interrupt circuits consist of Interrupt enable register (IENH, IENL), Interrupt request flags of IRQH, IRQL, Interrupt Edge Selection Register (IEDS), priority circuit and Master enable flag("I" flag of PSW). The configuration of interrupt circuit is shown in Figure 18-1 and Interrupt priority is shown in Table 18-1 . The External Interrupts INT0 and INT1 can each be transition-activated (1-to-0, 0-to-1 and both transiton). The flags that actually generate these interrupts are bit INT0IFand INT1IF in Register IRQH. When an external interrupt is generated, the flag that generated it is cleared by the hardware when the service routine is vectored to
Internal bus line I-flag is in PSW, it is cleared by "DI", set by "EI" instruction.When it goes interrupt service, I-flag is cleared by hardware, thus any other interrupt are inhibited. When interrupt service is completed by "RETI" instruction, I-flag is set to "1" by hardware.
only if the interrupt was transition-activated. The Timer 0 and Timer 1 Interrupts are generated by T0IF, T1IF, which are set by a match in their respective timer/ counter register. The AD converter Interrupt is generated by ADIF which is set by finishing the analog to digital conversion. The Watch dog timer Interrupt is generated by WDTIF which set by a match in Watch dog timer register ( when the bit WDTON is set to "0"). The Basic Interval Timer Interrupt is generated by BITIF which is set by a overflowing of the Basic Interval Timer Register(BITR). .
IENH IRQH External Int. 0
IEDS INT0IF INT1IF
Interrupt Enable Register (Higher byte)
7 6 Priority Control 5 4
Release STOP
External Int. 1 Timer 0 Timer 1 A/D Converter WDT BIT
T0IF T1IF
To CPU I Flag Interrupt Master Enable Flag Interrupt Vector Address Generator
ADIF WDTIF BITIF
7 6 5
IRQL
IENL
Interrupt Enable Register (Lower byte)
Internal bus line
Figure 18-1 Block Diagram of Interrupt Function
The interrupts are controlled by the interrupt master enable flag I-flag (bit 2 of PSW), the interrupt enable register (IENH, IENL) and the interrupt request flags (in IRQH, IRQL) except Power-on reset and software BRK interrupt. Interrupt enable registers are shown in Figure 18-2 . These registers are composed of interrupt enable flags of each interrupt source, these flags determines whether an interrupt will be accepted or not. When enable flag is "0", a corresponding interrupt source is prohibited. Note that PSW contains also a master enable bit, I-flag, which disables all interrupts at once.
Reset/Interrupt Hardware Reset External Interrupt 0 External Interrupt 1 Timer 0 Timer 1 A/D Converter Watch Dog Timer Basic Interval Timer
Symbol RESET INT0 INT1 Timer 0 Timer 1 A/D C WDT BIT
Priority 1 2 3 4 5 6 7
Vector Addr. FFFEH FFFAH FFF8H FFF6H FFF4H FFEAH FFE8H FFE6H
Table 18-1 Interrupt Priority
Oct. 1999 ver 1.0
53
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
Interrupt Enable Register High IENH INT0E INT1E T0E T1E ADDRESS : E2H RESET VALUE : 0000----
Interrupt Enable Register Low IENL ADE WDTE BITE ADDRESS : E3H RESET VALUE : 000-----
Enables or disables the interrupt individually If flag is cleared, the interrupt is disabled. 0 : Disable 1 : Enable Interrupt Request Register High IRQH INT0IF INT1IF T0IF T1IF ADDRESS : E4H RESET VALUE : 0000----
Interrupt Request Register Low IRQL ADIF WDTIF BITIF ADDRESS : E5H RESET VALUE : 000-----
Shows the interrupt occurrence 0 : Not occurred 1 : Interrupt request is occurred
Figure 18-2 Interrupt Enable Registers and Interrupt Request Registers
When an interrupt is occured, the I-flag is cleared and disable any further interrupt, the return address and PSW are pushed into the stack and the PC is vectored to. Once in the interrupt service routine the source(s) of the interrupt can be determined by polling the interrupt request flag bits.
The interrupt request flag bit(s) must be cleared by software before re-enabling interrupts to avoid recursive interrupts. The Interrupt Request flags are able to be read and written.
18.1 Interrupt Sequence
An interrupt request is held until the interrupt is accepted or the interrupt latch is cleared to "0" by a reset or an instruction. Interrupt acceptance sequence requires 8 f OSC (2 s at fXIN=4MHz) after the completion of the current instruction execution. The interrupt service task is terminated upon execution of an interrupt return instruction [RETI]. Interrupt acceptance 1. The interrupt master enable flag (I-flag) is cleared to "0" to temporarily disable the acceptance of any following maskable interrupts. When a non-maskable interrupt is accepted, the acceptance of any following interrupts is temporarily disabled. 2. Interrupt request flag for the interrupt source accepted is cleared to "0". 3. The contents of the program counter (return address) and the program status word are saved (pushed) onto the stack area. The stack pointer decreases 3 times. 4. The entry address of the interrupt service program is read from the vector table address and the entry address is loaded to the program counter. 5. The instruction stored at the entry address of the interrupt service program is executed.
54
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
System clock
Instruction Fetch Address Bus
PC SP SP-1 SP-2 V.L. V.H. New PC
Data Bus Internal Read Internal Write
Not used
PCH
PCL
PSW
V.L.
ADL
ADH
OP code
Interrupt Processing Step V.L. and V.H. are vector addresses. ADL and ADH are start addresses of interrupt service routine as vector contents.
Interrupt Service Task
Figure 18-3 Timing chart of Interrupt Acceptance and Interrupt Return Instruction
Basic Interval Timer Vector Table Address
Entry Address
The following method is used to save/restore the generalpurpose registers. Example: Register save using push and pop instructions
0FFE6H 0FFE7H
012H 0E3H
0E312H 0E313H
0EH 2EH
INTxx:
PUSH PUSH PUSH
A X Y
;SAVE ACC. ;SAVE X REG. ;SAVE Y REG.
Correspondence between vector table address for BIT interrupt and the entry address of the interrupt service program.
interrupt processing
A interrupt request is not accepted until the I-flag is set to "1" even if a requested interrupt has higher priority than that of the current interrupt being serviced. When nested interrupt service is required, the I-flag should be set to "1" by "EI" instruction in the interrupt service program. In this case, acceptable interrupt sources are selectively enabled by the individual interrupt enable flags. Saving/Restoring General-purpose Register During interrupt acceptance processing, the program counter and the program status word are automatically saved on the stack, but accumulator and other registers are not saved itself. These registers are saved by the software if necessary. Also, when multiple interrupt services are nested, it is necessary to avoid using the same data memory area for saving registers.
POP POP POP RETI
Y X A
;RESTORE Y REG. ;RESTORE X REG. ;RESTORE ACC. ;RETURN
General-purpose register save/restore using push and pop instructions;
main task acceptance of interrupt interrupt service task saving registers
restoring registers interrupt return
Oct. 1999 ver 1.0
55
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
18.2 BRK Interrupt
Software interrupt can be invoked by BRK instruction, which has the lowest priority order. Interrupt vector address of BRK is shared with the vector of TCALL 0 (Refer to Program Memory Section). When BRK interrupt is generated, B-flag of PSW is set to distinguish BRK from TCALL 0. Each processing step is determined by B-flag as shown in Figure 18-4.
TIMER1: PUSH PUSH PUSH LDM LDM EI : : : : : : LDM LDM POP POP POP RETI A X Y IENH,#80H IENL,#0
;Enable INT0 only ;Disable other ;Enable Interrupt
IENH,#0FFH ;Enable all interrupts IENL,#0F0H Y X A
B-FLAG BRK or TCALL0 =1 BRK INTERRUPT ROUTINE RETI
=0
TCALL0 ROUTINE Main Program service
RET
TIMER 1 service INT0 service
enable INT0 disable other EI
Figure 18-4 Execution of BRK/TCALL0
Occur TIMER1 interrupt
Occur INT0
18.3 Multi Interrupt
If two requests of different priority levels are received simultaneously, the request of higher priority level is serviced. If requests of the interrupt are received at the same time simultaneously, an internal polling sequence determines by hardware which request is serviced. However, multiple processing through software for special features is possible. Generally when an interrupt is accepted, the I-flag is cleared to disable any further interrupt. But as user sets I-flag in interrupt routine, some further interrupt can be serviced even if certain interrupt is in progress. Example: Even though Timer1 interrupt is in progress, INT0 interrupt serviced without any suspend.
enable INT0 enable other
In this example, the INT0 interrupt can be serviced without any pending, even TIMER1 is in progress. Because of re-setting the interrupt enable registers IENH,IENL and master enable "EI" in the TIMER1 routine.
Figure 18-5 Execution of Multi Interrupt
56
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
18.4 External Interrupt
The external interrupt on INT0 and INT1 pins are edge triggered depending on the edge selection register IEDS (address 0E6H) as shown in Figure 18-6 . The edge detection of external interrupt has three transition activated mode: rising edge, falling edge, and both edge .
INT1 edge select 00: Int. disable 01: falling 10: rising 11: both INT0 edge select 00: Int. disable 01: falling 10: rising 11: both Ext. Interrupt Edge Selection Register W WW W IEDS W
ADDRESS : 0E6H RESET VALUE : 00000000 W W W
edge selection
INT0 pin
INT0IF
INT0 INTERRUPT
INT1 pin
INT1IF
INT1 INTERRUPT
IEDS [0E6H]
Figure 18-6 External Interrupt Block Diagram
Response Time The INT0 and INT1 edge are latched into INT0IF and INT1IF at every machine cycle. The values are not actually polled by the circuitry until the next machine cycle. If a request is active and conditions are right for it to be acknowledged, a hardware subroutine call to the requested service routine will be the next instruction to be executed. The DIV itself takes twelve cycles. Thus, a minimum of twelve complete machine cycles elapse between activation of an external interrupt request and the beginning of execution of the first instruction of the service routine. Below shows interrupt response timings.
Example: To use as an INT0 and INT1
: : ;**** Set port as an input port RB2,RB3 LDM RBIO,#1111_0011B ; ; ;**** Set port as an interrupt port LDM RBFUNC,#0C0H ; ; ;**** Set Falling-edge Detection LDM IEDS,#0000_0101B : :
max. 12 fOSC
8 fOSC
Interrupt Interrupt goes latched active
Interrupt processing
Interrupt routine
Figure 18-7 Interrupt Response Timing Diagram
Oct. 1999 ver 1.0
57
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
19. WATCHDOG TIMER
The purpose of the watchdog timer is to detect the malfunction (runaway) of program due to external noise or other causes and return the operation to the normal condition. The watchdog timer has two types of clock source. The first type is an on-chip RC oscillator which does not require any external components. This RC oscillator is separate from the external oscillator of the Xin pin. It means that the watchdog timer will run, even if the clock on the Xin pin of the device has been stopped, for example, by entering the STOP mode. The other type is a prescaled system clock. The watchdog timer consists of 7-bit binary counter and the watchdog timer data register. The source clock of WDT is overflow of Basic Interval Timer. When the value of 7-bit binary counter is equal to the lower 7 bits of WDTR, the interrupt request flag is generated. This can be used as WDT interrupt or CPU reset signal in accordance with the bit WDTON .
Note: Because the watchdog timer counter is enabled after clearing Basic Interval Timer, after the bit WDTON set to "1", maximum error of timer is depend on prescaler ratio of Basic Interval Timer.
The 7-bit binary counter is cleared by setting WDTCL(bit7 of WDTR) and the WDTCL is cleared automatically after 1 machine cycle. The RC oscillated watchdog timer is activated by setting the bit RCWDT of CKCTLR and executing the STOP instruction as shown below.
: LDM LDM STOP NOP NOP : CKCTLR,#3FH WDTR,#0FFH ; enable the RC-osc WDT ; set the WDT period ; enter the STOP mode ; RC-osc WDT running
The RC oscillation period is variable according to the temperature, VDD and process variations from part to part (approximately, 120~180uS). The following equation shows the RC oscillated watchdog timer time-out. T R C W D T = C L K R C x28x[W D T R .6~ 0]+ (C L K R C x28)/2 w here, C L K R C = 120~ 180uS In addition, this watchdog timer can be used as a simple 7bit timer by interrupt WDTIF. The interval of watchdog timer interrupt is decided by Basic Interval Timer. Interval equation is as below. TWDT = [WDTR.6~0] x Interval of BIT
Clock Control Register CKCTLR WAKEUP RCWDT 0 X WDTON 1 BTCL X BTS2 X BTS1 X BTS0 X ADDRESS : ECH RESET VALUE : -0010111 Bit Manipulation Not Available
Watchdog Timer Register WDTR WDTCL
7-bit Watchdog Counter Register
ADDRESS : EDH RESET VALUE : 01111111 Bit Manipulation Not Available
RCWDT BTS[2:0]
fxin
/8 / 16 / 32 / 64 / 128 / 256 / 512 / 1024
WDTR (8-bit) 3
BTCL Clear
WDTCL
WDTON
8 MUX
0 BITR ( 8-bit ) 1 7-bit Counter OFD
1
CPU RESET
0 Overflow Detection Watchdog Timer Interrupt Request
Internal RC OSC
BITIF
Basic Interval Timer Interrupt
Figure 19-1 Block Diagram of Watchdog Timer
58
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
20. Power Saving Mode
For applications where power consumption is a critical factor, device provides three kinds of power saving functions, STOP mode, Wake-up Timer mode and internal RCoscillated watchdog timer mode. The power saving function is activated by execution of STOP instruction after setting the corresponding bit (WAKEUP, RCWDT) of CKCTLR. Table 20-1 shows the status of each Power Saving Mode
Peripheral RAM Control Registers I/O Ports CPU Timer0 Oscillation Prescaler Internal RC oscillator Entering Condition CKCTLR[6,5] Power Saving Release Source STOP Retain Retain Retain Stop Stop Stop Stop Stop 00 RESET, INT0, INT1 Wake-up Timer Retain Retain Retain Stop Operation Oscillation / 2048 only Stop 1X RESET, INT0, INT1, Timer0 Internal RC-WDT Retain Retain Retain Stop Stop Stop Stop Oscillation 01 RESET, INT0, INT1, RC-WDT
Note: Before executing STOP instruction, clear all interrupt request flag. Because if the interrupt request flag is set before STOP instruction, the MCU runs as if it doesn't perform STOP instruction, even though the STOP instruction is completed. So insert two lines to clear all interrupt request flags (IRQH, IRQL) before STOP instruction as shown each example.
Table 20-1 Power Saving Mode
20.1 Stop Mode
In the Stop mode, the on-chip oscillator is stopped. With the clock frozen, all functions are stopped, but the on-chip RAM and Control registers are held. The port pins out the values held by their respective port data register, port direction registers. Oscillator stops and the systems internal operations are all held up. * The states of the RAM, registers, and latches valid immediately before the system is put in the STOP state are all held. * The program counter stop the address of the instruction to be executed after the instruction "STOP" which starts the STOP operating mode. The Stop mode is activated by execution of STOP instruction after setting the bit WAKEUP and RCWDT of CKCTLR to "00". (This register should be written by byte operation. If this register is set by bit manipulation instruction, for example "set1" or "clr1" instruction, it may be undesired operation) In the Stop mode of operation, VDD can be reduced to minimize power consumption. Care must be taken, however, to ensure that VDD is not reduced before the Stop mode is invoked, and that VDD is restored to its normal operating level, before the Stop mode is terminated. The reset should not be activated before VDD is restored to its normal operating level, and must be held active long enough to allow the oscillator to restart and stabilize.
Note: After STOP instruction, at least two or more NOP instruction should be written
Ex) LDM CKCTLR,#0000_1110B LDM IRQH,#0 LDM IRQL,#0 STOP NOP NOP
In the STOP operation, the dissipation of the power associated with the oscillator and the internal hardware is lowered; however, the power dissipation associated with the pin interface (depending on the external circuitry and program) is not directly determined by the hardware operation of the STOP feature. This point should be little current flows when the input level is stable at the power voltage
Oct. 1999 ver 1.0
59
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
level (VDD/VSS), however, when the input level gets higher than the power voltage level (by approximately 0.3 to 0.5V), a current begins to flow. Therefore, if cutting off the output transistor at an I/O port puts the pin signal into the high-impedance state, a current flow across the ports input transistor, requiring to fix the level by pull-up or other means. Release the STOP mode The exit from STOP mode is hardware reset or external interrupt. Reset re-defines all the Control registers but does not change the on-chip RAM. External interrupts allow both on-chip RAM and Control registers to retain their values. After releasing STOP mode, instruction execution is divided into two ways by I-flag(bit2 of PSW). If I-flag = 1, the normal interrupt response takes place. If Iflag = 0, the chip will resume execution starting with the instruction following the STOP instruction. It will not vector to interrupt service routine. (refer to Figure 20-1) When exit from Stop mode by external interrupt, enough oscillation stabilization time is required to normal operation. Figure 20-2 shows the timing diagram. When release the Stop mode, the Basic interval timer is activated on wake-up. It is increased from 00H until FFH. The count overflow is set to start normal operation. Therefore, before STOP instruction, user must be set its relevant prescaler divide ratio to have long enough time (more than 20msec). This guarantees that oscillator has started and stabilized. By reset, exit from Stop mode is shown in Figure 20-3. Minimizing Current Consumption in Stop Mode The Stop mode is designed to reduce power consumption. To minimize the current consumption during Stop mode, the user should turn-off output drivers that are sourcing or
sinking current, if it is practical. Weak pull-ups on port pins should be turned off, if possible. All inputs should be either as VSS or at VDD (or as close to rail as possible). An intermediate voltage on an input pin causes the input buffer to draw a significant amount of current.
STOP INSTRUCTION STOP Mode
Interrupt Request =0
Corresponding Interrupt Enable Bit (IENH, IENL)
IEXX =1
STOP Mode Release
Master Interrupt Enable Bit PSW[2]
I-FLAG =1
=0
Interrupt Service Routine
Next INSTRUCTION
Figure 20-1 STOP Releasing Flow by Interrupts
~ ~
Oscillator (XIN pin) Internal Clock External Interrupt
~ ~
STOP Instruction Execution
~~ ~~ ~ ~
Clear Basic Interval Timer
~ ~ ~ ~ ~ ~
BIT Counter
N-2
N-1
N
N+1
N+2
00
01
FE
FF
00
01
~ ~
Normal Operation
STOP Mode
Stabilization Time tST > 20mS
Normal Operation
Figure 20-2 Timing of STOP Mode Release by External Interrupt
60
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
STOP Mode
~ ~
Oscillator (XIN pin) Internal Clock RESET Internal RESET
~ ~
STOP Instruction Execution Time can not be controlled by software
Figure 20-3 Timing of STOP Mode Release by RESET
~~ ~~ ~ ~ ~ ~
Stabilization Time tST = 64mS @4MHz
~~ ~~ ~ ~
20.2 Wake-up Timer Mode
In the Wake-up Timer mode, the on-chip oscillator is not stopped. Except the Prescaler (only 2048 divided ratio) and Timer0, all functions are stopped, but the on-chip RAM and Control registers are held. The port pins out the values held by their respective port data register, port direction registers. The Wake-up Timer mode is activated by execution of STOP instruction after setting the bit WAKEUP of CKCTLR to "1". (This register should be written by byte operation. If this register is set by bit manipulation instruction, for example "set1" or "clr1" instruction, it may be undesired operation)
Note: After STOP instruction, at least two or more NOP instruction should be written Ex) LDM TDR0,#0FFH LDM TM0,#0001_1011B LDM CKCTLR,#0100_1110B LDM IRQH,#0 LDM IRQL,#0 STOP NOP NOP
In addition, the clock source of timer0 should be selected to 2048 divided ratio. Otherwise, the wake-up function can not work. And the timer0 can be operated as 16-bit timer with timer1 (refer to timer function). The period of wake-up function is varied by setting the timer data register 0, TDR0. Release the Wake-up Timer mode The exit from Wake-up Timer mode is hardware reset, Timer0 overflow or external interrupt. Reset re-defines all the Control registers but does not change the on-chip RAM. External interrupts and Timer0 overflow allow both on-chip RAM and Control registers to retain their values. If I-flag = 1, the normal interrupt response takes place. If Iflag = 0, the chip will resume execution starting with the instruction following the STOP instruction. It will not vector to interrupt service routine (refer to Figure 20-1). When exit from Wake-up Timer mode by external interrupt or timer0 overflow, the oscillation stabilization time is not required to normal operation. Because this mode do not stop the on-chip oscillator shown as Figure 20-4.
~ ~
Oscillator (XIN pin) CPU Clock Interrupt Request
STOP Instruction Execution
~~ ~~ ~ ~
Normal Operation
Wake-up Timer Mode (stop the CPU clock)
Normal Operation Do not need Stabilization Time
Figure 20-4 Wake-up Timer Mode Releasing by External Interrupt or Timer0 Interrupt
Oct. 1999 ver 1.0
61
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
20.3 Internal RC-Oscillated Watchdog Timer Mode
In the Internal RC-Oscillated Watchdog Timer mode, the on-chip oscillator is stopped. But internal RC oscillation circuit is oscillated in this mode. The on-chip RAM and Control registers are held. The port pins out the values held by their respective port data register, port direction registers. The Internal RC-Oscillated Watchdog Timer mode is activated by execution of STOP instruction after setting the bit WAKEUP and RCWDT of CKCTLR to "01". (This register should be written by byte operation. If this register is set by bit manipulation instruction, for example "set1" or "clr1" instruction, it may be undesired operation)
Note: After STOP instruction, at least two or more NOP instruction should be written
Ex) LDM LDM LDM LDM STOP NOP NOP WDTR,#1111_1111B CKCTLR,#0010_1110B IRQH,#0 IRQL,#0
chip RAM. External interrupts allow both on-chip RAM and Control registers to retain their values. If I-flag = 1, the normal interrupt response takes place. In this case, if the bit WDTON of CKCTLR is set to "0" and the bit WDTE of IENH is set to "1", the device will execute the watchdog timer interrupt service routine.(Figure 20-5) However, if the bit WDTON of CKCTLR is set to "1", the device will generate the internal RESET signal and execute the reset processing. (Figure 20-6) If I-flag = 0, the chip will resume execution starting with the instruction following the STOP instruction. It will not vector to interrupt service routine (refer to Figure 20-1). When exit from Internal RC-Oscillated Watchdog Timer mode by external interrupt, the oscillation stabilization time is required for normal operation. Figure 20-5 shows the timing diagram. When release the Internal RC-Oscillated Watchdog Timer mode, the basic interval timer is activated on wake-up. It is increased from 00H until FFH. The count overflow is set to start normal operation. Therefore, before STOP instruction, user must be set its relevant prescaler divide ratio to have long enough time (more than 20msec). This guarantees that oscillator has started and stabilized. By reset, exit from internal RC-Oscillated Watchdog Timer mode is shown in Figure 20-6.
Release the Internal RC-Oscillated Watchdog Timer mode The exit from Internal RC-Oscillated Watchdog Timer mode is hardware reset or external interrupt. Reset re-defines all the Control registers but does not change the on-
~ ~
Oscillator (XIN pin) Internal RC Clock
~ ~
~ ~ ~ ~
Internal Clock External Interrupt (or WDT Interrupt)
~ ~
STOP Instruction Execution
~ ~
Clear Basic Interval Timer
~ ~ ~ ~
BIT Counter
N-2
N-1
N
N+1
N+2
00
01
FE
FF
00
00
~ ~
Normal Operation
RCWDT Mode
Stabilization Time tST > 20mS
Normal Operation
Figure 20-5 Internal RCWDT Mode Releasing by External Interrupt or WDT Interrupt
62
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
RCWDT Mode
~ ~
Oscillator (XIN pin) Internal RC Clock
~ ~
~ ~ ~ ~
Internal Clock RESET RESET by WDT Internal RESET
~ ~
STOP Instruction Execution Time can not be controlled by software
Figure 20-6 Internal RCWDT Mode Releasing by RESET.
INPUT PIN VDD VDD internal pull-up i VDD OPEN
~ ~ ~ ~
Stabilization Time tST = 64mS @4MHz
~ ~ ~ ~
VDD
INPUT PIN
i=0
O
i GND VDD
O
i=0
Very weak current flows
X
Weak pull-up current flows OPEN
X O
GND
O
When port is configured as an input, input level should be closed to 0V or 5V to avoid power consumption.
Figure 20-7 Application Example of Unused Input Por t
OUTPUT PIN ON OPEN ON OFF i GND ON OFF VDD OFF ON L OFF i GND ON i=0 GND OUTPUT PIN VDD L VDD
O
OFF
X
X O
O
In the left case, Tr. base current flows from port to GND. To avoid power consumption, there should be low output to the port .
In the left case, much current flows from port to GND.
Figure 20-8 Application Example of Unused input Port
Oct. 1999 ver 1.0
63
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
21. RESET
The reset input is the RESET pin, which is the input to a Schmitt Trigger. A reset in accomplished by holding the RESET pin low for at least 8 oscillator periods, while the oscillator running. After reset, 64ms (at 4 MHz) add with 7 oscillator periods are required to start execution as shown in Figure 21-1 . Internal RAM is not affected by reset. When VDD is turned on, the RAM content is indeterminate. Therefore, this RAM should be initialized before reading or testing it. Initial state of each register is shown as Table 11-3 .
1
2
3
4
5
6
7
~ ~
Oscillator (XIN pin) RESET
~ ~ ~ ~
ADDRESS BUS DATA BUS
?
?
?
?
FFFE FFFF Start
~~ ~~
?
?
?
?
FE
ADL
ADH
OP
Stabilization Time tST = 64mS at 4MHz
Figure 21-1 Timing Diagram after RESET
~ ~
MAIN PROGRAM RESET Process Step
64
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
22. POWER FAIL PROCESSOR
The GMS87C1202 has an on-chip power fail detection circuitry to immunize against power noise. A configuration register, PFDR, can enable (if clear/programmed) or disable (if set) the Power-fail Detect circuitry. If VDD falls below 3.0~4.0V range for longer than 50 nS, the Power fail situation may reset MCU according to PFR bit of PFDR. As below PFDR register is not implemented on the in-circuit emulator, user can not experiment with it. Therefore, after final development of user program, this function may be experimented.
Note: Power fail processor function is not available on 3V operation, because this function will detect power fail all the time.
Power Fail Detector Register PFDR Reserved PFDIS PFDM PFS ADDRESS : EFH RESET VALUE : -----100
Power Fail Status 0 : Normal Operate 1 : This bit force to "1" when Power fail was detected Operation Mode 0 : Normal operation regardless of power fail 1 : MCU will be reset during power fail Disable Flag 0 : Power fail detection enable 1 : Power fail detection disable
Figure 22-1 Power Fail Detector Register
RESET VECTOR
PFS =1 NO RAM CLEAR INITIALIZE RAM DATA
YES
Skip the initial routine
INITIALIZE ALL PORTS INITIALIZE REGISTERS
FUNTION EXECUTION
Figure 22-2 Example S/W of RESET by Power fail
Oct. 1999 ver 1.0
65
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
VDD 64mS
PFVDDMAX PFVDDMIN
Internal RESET VDD When PFDM = 1 Internal RESET VDD t < 64mS
64mS
PFVDDMAX PFVDDMIN
PFVDDMAX PFVDDMIN 64mS
Internal RESET
Figure 22-3 Power Fail Processor Situations
66
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
23. OTP PROGRAMMING
The GMS87C1102/1202T is one-time PROM(OTP) microcontroller with 2K bytes electrically programmable read only memory for the GMS87C1102/1202 system evaluation, first production and fast mass production. To programming the OTP device, user must use the universal programmer which is support HYUNDAI MicroElectronics microcontrollers.
23.1 Program Memory MAP
Program Memory consists of configuration area and user program memory area. The configuration memory area has two parts (User ID & System Configuration Bits), the areas are shown below in Figure 1-1. The Device Configuration Area can be programmed or left unprogrammed to select device configuration such as security bit. Ten memory locations (0F50 H ~ 0FE0H) are designated as Customer ID recording locations where the user can store checksum or other customer identification numbers. This area is not accessible during normal execution but is readable and writable during program / verify.
0F50H DEVICE CONFIGURATION AREA 0FF0H ID ID ID ID ID ID ID ID ID ID CONFIG Configuration Register CONFIG 0F50H 0F60H 0F70H 0F80H 0F90H 0FA0H 0FB0H 0FC0H 0FD0H 0FE0H 0FF0H
-
-
-
-
-
LOCK
-
RC
ADDRESS : 0FF0H RC Option 0 : Normal Oscillator 1 : External RC Oscillator SECURITY BIT 0 : Allow Code Read Out 1 : Prohibit Code Read Out
Figure 23-1 Device Configuration Area
The Security Definition Method is explained below. 1) After writing "H" to code protect bit in Write & Verify Mode and getting out of Write & Verify Mode, user cannot read out the program code. But if not getting out of Write & Verify Mode (maintaining Programming Power VPP = 12.75V), user can verify Program code. 2) Regardless of Code protect, user can read out configuration Memory (User ID and Configuration Bits) 3) If user knows Security (Lock) state, user can read code protect bit in the System Configuration Bits.
Oct. 1999 ver 1.0
67
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
A_D4 A_D5 A_D6 A_D7 VDD CTL0 CTL1 CTL2
1 2
16 15
A_D3 A_D2 A_D1 A_D0 VSS VPP NC EPROM Enable
GMS87C1102
3 4 5 6 7 8
14 13 12 11 10 9
Figure 23-2 Pin Assignment User Mode Pin No. Pin Name
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 RA4 (AN4) RA5 (AN5) RA6 (AN6) RA7 (AN7) VDD RB0 (AVref/AN0) RB2 (INT0) RB4 (PWM/COMP) XIN XOUT RESET VSS RA0 (EC0) RA1 (AN1) RA2 (AN2) RA3 (AN3)
EPROM MODE Pin Name
A_D4 A_D5 A_D6 A_D7 VDD CTL0 CTL1 CTL2 EPROM Enable NC VPP VSS A_D0 A_D1 A_D2 A_D3 Address Input Data Input/Output High Active, Latch Address in falling edge No connection Programming Power (0V, 12.75V) Connect to VSS (0V) A8 A9 A10 A11 A0 A1 A2 A3 D0 D1 D2 D3 Read/Write Control Address/Data Control Connect to VDD (6.0V) Address Input Data Input/Output
Description
A12 A13 A14 A15 A4 A5 A6 A7 D4 D5 D6 D7
Table 23-1 Pin Description in EPROM Mode
68
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
A_D4 A_D5 A_D6 A_D7 VDD CTL0 CTL1 CTL2
1 2 3
28 27 26
A_D3 A_D2 A_D1 A_D0
GMS87C1202
4 5 6 7 8 9 10
25 24 23 22 21 20 19 NC
VSS VPP
EPROM Enable
Figure 23-3 Pin Assignment
User Mode Pin No. Pin Name
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15,16 17 18 19 20 RA4 (AN4) RA5 (AN5) RA6 (AN6) RA7 (AN7) VDD RB0 (AVref/AN0) RB1 (BUZ) RB2 (INT0) RB3 (INT1) RB4 (PWM/COMP) XIN XOUT RESET VSS RC0, 1 RA0 (EC0) RA1 (AN1) RA2 (AN2) RA3 (AN3)
EPROM MODE Pin Name
A_D4 A_D5 A_D6 A_D7 VDD CTL0 CTL1 CTL2 VDD VDD EPROM Enable NC VPP VSS VDD A_D0 A_D1 A_D2 A_D3 Address Input Data Input/Output Connect to VDD (6.0V) Connect to VDD (6.0V) High Active, Latch Address in falling edge No connection Programming Power (0V, 12.75V) Connect to VSS (0V) Connect to VDD (6.0V) A8 A9 A10 A11 A0 A1 A2 A3 D0 D1 D2 D3 Read/Write Control Address/Data Control Connect to VDD (6.0V) Address Input Data Input/Output
Description
A12 A13 A14 A15 A4 A5 A6 A7 D4 D5 D6 D7
Table 23-2 Pin Description in EPROM Mode
Oct. 1999 ver 1.0
69
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
TSET1
THLD1
TDLY1
THLD2
TDLY2
~ ~
EPROM Enable
TVPPS VIHP
~ ~ ~ ~
~ ~
VPP
TVDDS TVPPR
CTL0
0V TCD1 VDD1H
~~ ~~
~~ ~~
VDD1H TCD1
CTL1 CTL2 A_D7~ A_D0
0V
~ ~
0V
TCD1
TCD1
~ ~
~ ~
~ ~
HA VDD1H
LA
DATA IN
DATA OUT
LA
DATA IN
DATA OUT
~ ~
~ ~
VDD
High 8bit Address Input Low 8bit Address Input Write Mode Verify Low 8bit Address Input Write Mode Verify
Figure 23-4 Timing Diagram in Program (Write & Verify) Mode
After input a high address, output data following low address input
TSET1 THLD1 TDLY1 THLD2 TDLY2
Anothe high address step
EPROM Enable
TVPPS VIHP
VPP
TVDDS TVPPR VDD2H
CTL0
0V
CTL1 CTL2 A_D7~ A_D0
0V
TCD2 VDD2H TCD1
TCD2
0V
TCD1
HA VDD2H
LA
DATA
LA
DATA
HA
LA
DATA
VDD
High 8bit Address Input Low 8bit Address Input DATA Output Low 8bit Address Input DATA Output High 8bit Address Input Low 8bit Address Input DATA Output
Figure 23-5 Timing Diagram in READ Mode
70
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
Parameter Programming Supply Current Supply Current in EPROM Mode VPP Level during Programming VDD Level in Program Mode VDD Level in Read Mode CTL2~0 High Level in EPROM Mode CTL2~0 Low Level in EPROM Mode A_D7~A_D0 High Level in EPROM Mode A_D7~A_D0 Low Level in EPROM Mode VDD Saturation Time VPP Setup Time VPP Saturation Time EPROM Enable Setup Time after Data Input EPROM Enable Hold Time after TSET1 EPROM Enable Delay Time after THLD1 EPROM Enable Hold Time in Write Mode EPROM Enable Delay Time after THLD2 CTL2,1 Setup Time after Low Address input and Data input CTL1 Setup Time before Data output in Read and Verify Mode
Symbol IVPP IVDDP VIHP VDD1H VDD2H VIHC VILC VIHAD VILAD TVDDS TVPPR TVPPS TSET1 THLD1 TDLY1 THLD2 TDLY2 TCD1 TCD2
MIN 12.0 5 0.8VDD 0.9VDD 1 1
TYP 12.5 6 2.7 200 500 200 100 200 100 100
MAX 50 20 13.0 6.5 0.2VDD 0.1VDD 1 -
Unit mA mA V V V V V V V mS mS mS nS nS nS nS nS nS nS
Table 23-3 AC/DC Requirements for Program/Read Mode
Oct. 1999 ver 1.0
71
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
START
Set VDD=VDD1H Verify fof all address Report Verify failure NO
Set VPP=VIHP
Report Programming failure NO
Verify OK YES
Verify blank YES First Address Location Next address location
Report Programming OK
N=1
Report Programming failure NO
VDD=Vpp=0v
END
EPROM Write 100uS program time
YES Verify pass
Verify pass YES Apply 3N program cycle
NO
NO Last address YES
Figure 23-6 Programming Flow Chart
72
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
START
Set VDD=VDD2H
Verify fof all address
Set VPP=VIHP
First Address Location Next address location NO
Last address YES Report Read OK
VDD=0V VPP=0V
END
Figure 23-7 Reading Flow Chart
Oct. 1999 ver 1.0
73
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
A. INSTRUCTION MAP
LOW 00000 HIGH 00
00001 01 SET1 dp.bit
00010 02
00011 03
00100 04 ADC #imm SBC #imm CMP #imm OR #imm AND #imm EOR #imm LDA #imm LDM dp,#imm
00101 05 ADC dp SBC dp CMP dp OR dp AND dp EOR dp LDA dp STA dp
00110 06 ADC dp+X SBC dp+X CMP dp+X OR dp+X AND dp+X EOR dp+X LDA dp+X STA dp+X
00111 07 ADC !abs SBC !abs CMP !abs OR !abs AND !abs EOR !abs LDA !abs STA !abs
01000 08 ASL A ROL A LSR A ROR A INC A DEC A TXA TAX
01001 09 ASL dp ROL dp LSR dp ROR dp INC dp DEC dp LDY dp STY dp
01010 0A TCALL 0
01011 0B SETA1 .bit
01100 0C BIT dp COM dp TST dp CMPX dp CMPY dp DBNE dp LDX dp STX dp
01101 0D POP A POP X POP Y POP PSW CBNE dp+X XMA dp+X LDX dp+Y STX dp+Y
01110 0E PUSH A PUSH X PUSH Y PUSH PSW TXSP TSPX XCN XAX
01111 0F BRK BRA rel PCALL Upage RET INC X DEC X DAS STOP
000 001 010 011 100 101 110 111
CLRC CLRG DI CLRV SETC SETG EI
BBS BBS A.bit,rel dp.bit,rel
TCALL CLRA1 2 .bit TCALL 4 TCALL 6 NOT1 M.bit OR1 OR1B
TCALL AND1 8 AND1B TCALL EOR1 10 EOR1B TCALL 12 TCALL 14 LDC LDCB STC M.bit
LOW 10000 HIGH 10
10001 11 CLR1
dp.bit
10010 12 BBC
A.bit,rel
10011 13 BBC
dp.bit,rel
10100 14 ADC {X} SBC {X} CMP {X} OR {X} AND {X} EOR {X} LDA {X} STA {X}
10101 15 ADC !abs+Y SBC !abs+Y CMP !abs+Y OR !abs+Y AND !abs+Y EOR !abs+Y LDA !abs+Y STA !abs+Y
10110 16 ADC [dp+X] SBC [dp+X] CMP [dp+X] OR [dp+X] AND [dp+X] EOR [dp+X] LDA [dp+X] STA [dp+X]
10111 17 ADC [dp]+Y SBC [dp]+Y CMP [dp]+Y OR [dp]+Y AND [dp]+Y EOR [dp]+Y LDA [dp]+Y STA [dp]+Y
11000 18 ASL !abs ROL !abs LSR !abs ROR !abs INC !abs DEC !abs LDY !abs STY !abs
11001 19 ASL dp+X ROL dp+X LSR dp+X ROR dp+X INC dp+X DEC dp+X LDY dp+X STY dp+X
11010 1A TCALL 1 TCALL 3 TCALL 5 TCALL 7 TCALL 9 TCALL 11 TCALL 13 TCALL 15
11011 1B JMP !abs CALL !abs MUL DBNE Y DIV XMA {X} LDA {X}+ STA {X}+
11100 1C BIT !abs TEST !abs
11101 1D ADDW dp SUBW dp
11110 1E LDX #imm LDY #imm CMPX #imm CMPY #imm INC Y DEC Y XAY XYX
11111 1F JMP [!abs] JMP [dp] CALL [dp] RETI TAY TYA DAA NOP
000 001 010 011 100 101 110 111
BPL rel BVC rel BCC rel BNE rel BMI rel BVS rel BCS rel BEQ rel
TCLR1 CMPW !abs dp CMPX !abs CMPY !abs XMA dp LDX !abs STX !abs LDYA dp INCW dp DECW dp STYA dp CBNE dp
74
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
B. INSTRUCTION SET
1. ARITHMETIC/ LOGIC OPERATION
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 MNEMONIC ADC #imm ADC dp ADC dp + X ADC !abs ADC !abs + Y ADC [ dp + X ] ADC [ dp ] + Y ADC { X } AND #imm AND dp AND dp + X AND !abs AND !abs + Y AND [ dp + X ] AND [ dp ] + Y AND { X } ASL A ASL dp ASL dp + X ASL !abs CMP #imm CMP dp CMP dp + X CMP !abs CMP !abs + Y CMP [ dp + X ] CMP [ dp ] + Y CMP { X } CMPX #imm CMPX dp CMPX !abs CMPY #imm CMPY dp CMPY !abs COM dp DAA DAS DEC A DEC dp DEC dp + X DEC !abs DEC X DEC Y DIV OP BYTE CYCLE CODE NO NO 04 2 2 05 06 07 15 16 17 14 84 85 86 87 95 96 97 94 08 09 19 18 44 45 46 47 55 56 57 54 5E 6C 7C 7E 8C 9C 2C DF CF A8 A9 B9 B8 AF BE 9B 2 2 3 3 2 2 1 2 2 2 3 3 2 2 1 1 2 2 3 2 2 2 3 3 2 2 1 2 2 3 2 2 3 2 1 1 1 2 2 3 1 1 1 3 4 4 5 6 6 3 2 3 4 4 5 6 6 3 2 4 5 5 2 3 4 4 5 6 6 3 2 3 4 2 3 4 4 3 3 2 4 5 5 2 2 12 Divide : YA / X Q: A, R: Y NV--H-Z1'S Complement : ( dp ) ~( dp ) Decimal adjust for addition Decimal adjust for subtraction Decrement M (M)-1 N-----ZN-----ZN-----ZC N-----ZC N-----ZCompare Y contents with memory contents (Y)-(M) N-----ZC Compare X contents with memory contents (X)-(M) N-----ZC N-----ZC Compare accumulator contents with memory contents (A) -(M) Arithmetic shift left C 76543210 "0" N-----ZC N-----ZLogical AND A (A)(M) NV--H-ZC OPERATION Add with carry. A(A)+(M)+C FLAG NVGBHIZC
Oct. 1999 ver 1.0
75
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
NO. 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89
MNEMONIC EOR #imm EOR dp EOR dp + X EOR !abs EOR !abs + Y EOR [ dp + X ] EOR [ dp ] + Y EOR { X } INC A INC dp INC dp + X INC !abs INC X INC Y LSR A LSR dp LSR dp + X LSR !abs MUL OR #imm OR dp OR dp + X OR !abs OR !abs + Y OR [ dp + X ] OR [ dp ] + Y OR { X } ROL A ROL dp ROL dp + X ROL !abs ROR A ROR dp ROR dp + X ROR !abs SBC #imm SBC dp SBC dp + X SBC !abs SBC !abs + Y SBC [ dp + X ] SBC [ dp ] + Y SBC { X } TST dp XCN
OP BYTE CYCLE CODE NO NO A4 2 2 A5 A6 A7 B5 B6 B7 B4 88 89 99 98 8F 9E 48 49 59 58 5B 64 65 66 67 75 76 77 74 28 29 39 38 68 69 79 78 24 25 26 27 35 36 37 34 4C CE 2 2 3 3 2 2 1 1 2 2 3 1 1 1 2 2 3 1 2 2 2 3 3 2 2 1 1 2 2 3 1 2 2 3 2 2 2 3 3 2 2 1 2 1 3 4 4 5 6 6 3 2 4 5 5 2 2 2 4 5 5 9 2 3 4 4 5 6 6 3 2 4 5 5 2 4 5 5 2 3 4 4 5 6 6 3 3 5
OPERATION Exclusive OR A (A)(M)
FLAG NVGBHIZC
N-----Z-
Increment M (M)+1
N-----ZN-----Z-
Logical shift right 76543210 "0" Multiply : YA Y x A Logical OR A (A)(M) N-----ZN-----ZC N-----ZC
Rotate left through carry C 76543210 N-----ZC
Rotate right through carry 76543210 Subtract with carry A ( A ) - ( M ) - ~( C ) NV--HZC C N-----ZC
Test memory contents for negative or zero ( dp ) - 00H Exchange nibbles within the accumulator A7~A4 A3~A0
N-----ZN-----Z-
76
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
2. REGISTER / MEMORY OPERATION
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 MNEMONIC LDA #imm LDA dp LDA dp + X LDA !abs LDA !abs + Y LDA [ dp + X ] LDA [ dp ] + Y LDA { X } LDA { X }+ LDM dp,#imm LDX #imm LDX dp LDX dp + Y LDX !abs LDY #imm LDY dp LDY dp + X LDY !abs STA dp STA dp + X STA !abs STA !abs + Y STA [ dp + X ] STA [ dp ] + Y STA { X } STA { X }+ STX dp STX dp + Y STX !abs STY dp STY dp + X STY !abs TAX TAY TSPX TXA TXSP TYA XAX XAY XMA dp XMA dp+X XMA {X} XYX OP BYTE CYCLE CODE NO NO C4 2 2 C5 C6 C7 D5 D6 D7 D4 DB E4 1E CC CD DC 3E C9 D9 D8 E5 E6 E7 F5 F6 F7 F4 FB EC ED FC E9 F9 F8 E8 9F AE C8 8E BF EE DE BC AD BB FE 2 2 3 3 2 2 1 1 3 2 2 2 3 2 2 2 3 2 2 3 3 2 2 1 1 2 2 3 2 2 3 1 1 1 1 1 1 1 1 2 2 1 1 3 4 4 5 6 6 3 4 5 2 3 4 4 2 3 4 4 4 5 5 6 7 7 4 4 4 5 5 4 5 5 2 2 2 2 2 2 4 4 5 6 5 4 Exchange X-register contents with Y-register : X Y -------Transfer accumulator contents to X-register : X A Transfer accumulator contents to Y-register : Y A Transfer stack-pointer contents to X-register : X sp Transfer X-register contents to accumulator: A X Transfer X-register contents to stack-pointer: sp X Transfer Y-register contents to accumulator: A Y N-----ZN-----ZN-----ZN-----ZN-----ZN-----ZStore Y-register contents in memory (M) Y -------X- register auto-increment : ( M ) A, X X + 1 Store X-register contents in memory (M) X --------------Store accumulator contents in memory (M)A Load Y-register Y(M) N-----ZX- register auto-increment : A ( M ) , X X + 1 Load memory with immediate data : ( M ) imm Load X-register X (M) N-----Z-------N-----ZOPERATION Load accumulator A(M) FLAG NVGBHIZC
Exchange X-register contents with accumulator :X A -------Exchange Y-register contents with accumulator :Y A -------Exchange memory contents with accumulator (M)A N-----Z-
Oct. 1999 ver 1.0
77
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
3. 16-BIT OPERATION
NO. 1 2 3 4 5 6 7 MNEMONIC ADDW dp CMPW dp DECW dp INCW dp LDYA dp STYA dp SUBW dp OP BYTE CYCLE CODE NO NO 1D 5D BD 9D 7D DD 3D 2 2 2 2 2 2 2 5 4 6 6 5 5 5 OPERATION 16-Bits add without carry YA ( YA ) + ( dp +1 ) ( dp ) Compare YA contents with memory pair contents : (YA) - (dp+1)(dp) Decrement memory pair ( dp+1)( dp) ( dp+1) ( dp) - 1 Increment memory pair ( dp+1) ( dp) ( dp+1) ( dp ) + 1 Load YA YA ( dp +1 ) ( dp ) Store YA ( dp +1 ) ( dp ) YA 16-Bits substact without carry YA ( YA ) - ( dp +1) ( dp) FLAG NVGBHIZC NV--H-ZC N-----ZC N-----ZN-----ZN-----Z-------NV--H-ZC
4. BIT MANIPULATION
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 MNEMONIC AND1 M.bit AND1B M.bit BIT dp BIT !abs CLR1 dp.bit CLRA1 A.bit CLRC CLRG CLRV EOR1 M.bit EOR1B M.bit LDC M.bit LDCB M.bit NOT1 M.bit OR1 M.bit OR1B M.bit SET1 dp.bit SETA1 A.bit SETC SETG STC M.bit TCLR1 !abs TSET1 !abs OP BYTE CYCLE OPERATION CODE NO NO 8B 3 4 Bit AND C-flag : C ( C ) ( M .bit ) 8B 0C 1C y1 2B 20 40 80 AB AB CB CB 4B 6B 6B x1 0B A0 C0 EB 5C 3C 3 2 3 2 2 1 1 1 3 3 3 3 3 3 3 2 2 1 1 3 3 3 4 4 5 4 2 2 2 2 5 5 4 4 5 5 5 4 2 2 2 6 6 6 Bit AND C-flag and NOT : C ( C ) ~( M .bit ) Bit test A with memory : Z ( A ) ( M ) , N ( M7 ) , V ( M6 ) Clear bit : ( M.bit ) "0" Clear A bit : ( A.bit ) "0" Clear C-flag : C "0" Clear G-flag : G "0" Clear V-flag : V "0" Bit exclusive-OR C-flag : C ( C ) ( M .bit ) Load C-flag : C ( M .bit ) Load C-flag with NOT : C ~( M .bit ) Bit complement : ( M .bit ) ~( M .bit ) Bit OR C-flag : C ( C ) ( M .bit ) Bit OR C-flag and NOT : C ( C ) ~( M .bit ) Set bit : ( M.bit ) "1" Set A bit : ( A.bit ) "1" Set C-flag : C "1" Set G-flag : G "1" Store C-flag : ( M .bit ) C Test and clear bits with A : A - ( M ) , ( M ) ( M ) ~( A ) Test and set bits with A : A-(M), (M) (M)(A) ---------------------0 --0-----0--0---------C -------C -------C --------------C -------C ---------------------1 --1-----------N-----ZN-----ZFLAG NVGBHIZC -------C -------C MM----Z-
Bit exclusive-OR C-flag and NOT : C ( C ) ~(M .bit) -------C
78
Oct. 1999 ver 1.0
HYUNDAI MicroElectronics
GMS87C1102 / GMS87C1202
5. BRANCH / JUMP OPERATION
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 MNEMONIC BBC A.bit,rel BBC dp.bit,rel BBS A.bit,rel BBS dp.bit,rel BCC rel BCS rel BEQ rel BMI rel BNE rel BPL rel BRA rel BVC rel BVS rel CALL !abs CALL [dp] CBNE dp,rel CBNE dp+X,rel DBNE dp,rel DBNE Y,rel JMP !abs JMP [!abs] JMP [dp] PCALL upage OP BYTE CYCLE OPERATION CODE NO NO y2 2 4/6 Branch if bit clear : y3 3 5/7 if ( bit ) = 0 , then pc ( pc ) + rel x2 x3 50 D0 F0 90 70 10 2F 30 B0 3B 5F FD 8D AC 7B 1B 1F 3F 4F 2 3 2 2 2 2 2 2 2 2 2 3 2 3 3 3 2 3 3 2 2 4/6 5/7 2/4 2/4 2/4 2/4 2/4 2/4 4 2/4 2/4 8 8 5/7 6/8 5/7 4/6 3 5 4 6 U-page call M(sp) ( pcH ), sp sp - 1, M(sp) ( pcL ), sp sp - 1, pcL ( upage ), pcH "0FFH" . Table call : (sp) ( pcH ), sp sp - 1, M(sp) ( pcL ),sp sp - 1, pcL (Table vector L), pcH (Table vector H) -------Branch if bit set : if ( bit ) = 1 , then pc ( pc ) + rel Branch if carry bit clear if ( C ) = 0 , then pc ( pc ) + rel Branch if carry bit set if ( C ) = 1 , then pc ( pc ) + rel Branch if equal if ( Z ) = 1 , then pc ( pc ) + rel Branch if minus if ( N ) = 1 , then pc ( pc ) + rel Branch if not equal if ( Z ) = 0 , then pc ( pc ) + rel Branch if minus if ( N ) = 0 , then pc ( pc ) + rel Branch always pc ( pc ) + rel Branch if overflow bit clear if (V) = 0 , then pc ( pc) + rel Branch if overflow bit set if (V) = 1 , then pc ( pc ) + rel Subroutine call M( sp)( pcH ), spsp - 1, M(sp) (pcL), sp sp - 1, -------if !abs, pc abs ; if [dp], pcL ( dp ), pcH ( dp+1 ) . -------Compare and branch if not equal : if ( A ) ( M ) , then pc ( pc ) + rel. Decrement and branch if not equal : if ( M ) 0 , then pc ( pc ) + rel. Unconditional jump pc jump address -----------------------------------------------------------------------------FLAG NVGBHIZC ---------------
24
TCALL n
nA
1
8
--------
Oct. 1999 ver 1.0
79
GMS87C1102 / GMS87C1202
HYUNDAI MicroElectronics
6. CONTROL OPERATION & etc.
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 MNEMONIC BRK DI EI NOP POP A POP X POP Y POP PSW PUSH A PUSH X PUSH Y PUSH PSW RET OP BYTE CYCLE CODE NO NO 0F 60 E0 FF 0D 2D 4D 6D 0E 2E 4E 6E 6F 1 1 1 1 1 1 1 1 1 1 1 1 1 8 3 3 2 4 4 4 4 4 4 4 4 5 OPERATION FLAG NVGBHIZC
Software interrupt : B "1", M(sp) (pcH), sp sp-1, M(s) (pcL), sp sp - 1, M(sp) (PSW), sp sp -1, ---1-0-pcL ( 0FFDEH ) , pcH ( 0FFDFH) . Disable interrupts : I "0" Enable interrupts : I "1" No operation sp sp + 1, A M( sp ) sp sp + 1, X M( sp ) sp sp + 1, Y M( sp ) sp sp + 1, PSW M( sp ) M( sp ) A , sp sp - 1 M( sp ) X , sp sp - 1 M( sp ) Y , sp sp - 1 M( sp ) PSW , sp sp - 1 Return from subroutine -------sp sp +1, pcL M( sp ), sp sp +1, pcH M( sp ) Return from interrupt sp sp +1, PSW M( sp ), sp sp + 1, pcL M( sp ), sp sp + 1, pcH M( sp ) Stop mode ( halt CPU, stop oscillator ) restored --------------restored ------------0------1---------
14 15
RETI STOP
7F EF
1 1
6 3
80
Oct. 1999 ver 1.0

▲Up To Search▲

Price & Availability of GMS87C1202

	To Download GMS87C1202 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .